Cleaning; Transport; Storage; Maintenance - Scheppach 5906136938 Traduction Des Instructions D'origine

12. Cleaning

m Important!
Pull out the power plug before doing any cleaning and
maintenance work on the equipment. Risk of injury
from electric shock!
m Important!
Wait until the equipment has cooled down complete-
ly! Risk of burns!
m Important!
Always depressurize the equipment before carrying
out any cleaning and maintenance work! Risk of in-
jury!
We recommend that you clean the device immediate-
ly each time you have finished using it.
• Keep the equipment free of dirt and dust as far as
possible. Wipe the equipment with a clean cloth or
blow it down with compressed air at low pressure.
• We recommend that you clean the equipment im-
mediately after you use it.
• Clean the equipment regularly with a damp cloth
and some soft soap. Do not use cleaningagents or
solvents; these may be aggressive to the plastic
parts in the equipment. Ensure that no water can
get into the interior of the equipment.
• You must disconnect the hose and any spraying
tools from the compressor before cleaning. Do not
clean the compressor with water, solvents or the
like.

13. Transport

To change the position of the device, lift the transport
handle and pull the device to the new location.
When transporting the device in a vehicle it must be
secured to the loading bed with straps.

14. Storage

m Important!
Pull out the mains plug and ventilate the equipment
and all connected pneumatic tools. Switch off the
compressor and make sure that it is secured in such
a way that it cannot be started up again by any unau-
thorized person.
Store the device and its accessories in a dark, dry
and frost-proof place that is inaccessible to children.
The optimum storage temperature is between 5 and
30˚C.
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58
Store the electrical tool in its original packaging.
Cover the electrical tool in order to protect it from
dust and moisture. Store the operating manual with
the electrical tool.

15. Maintenance

You require the following for maintenance:
• Open-ended spanner 14 mm (2 units - not included
in the scope of supply)
• Allen key 4 mm (not included in the scope of supply)
m Important!
Pull out the power plug before doing any cleaning and
maintenance work on the equipment. Risk of injury
from electric shock!
m Important!
Wait until the equipment has cooled down complete-
ly! Risk of burns!
m Important!
Always depressurize the equipment before carrying
out any cleaning and maintenance work! Risk of in-
jury!
15.1 Changing the V-belt (Fig. H to K)
To change the V-belt on the compressor, please be
sure to disconnect the device from the mains. Once
the compressor has been successfully disconnect-
ed from the mains, remove the protective grate by
turning the plastic clips (42) 90° using pliers. Then
remove the screw (39) including washers (40) and
spacer sleeve (41), which connects the protective
grate (2) with the motor (4) using a 4mm Allen key.
Now undo the four screws (42) on the motor (4) with
two size 14 spanners, so that you can subsequently
slide the motor. It is now possible to change the V-belt
(3).
After successfully changing the V-belt, perform the
same steps in reverse order to bring the device back
into operational condition. Make sure the motor is
bolted at a right angle to the running direction, in or-
der to guarantee fault-free running of the V-belt.
15.2 Maintenance work on the pressure vessel
Important!
To ensure a long service life of the pressure vessel
(12) , drain off the condensed water by opening the
drain valve (21) each time after using. Release the
vessel pressure first (see 9.5). . Open the drain screw
by turning counter-clockwise (looking at the screw
from the bottom of the compressor) so that all the
condensed water can run out of the pressure vessel.
Then close the drain screw again (turn it clockwise).
Check the pressure vessel for signs of rust and dam-
age each time before using.
GB | 25