Master/Slave Mode - HQ Power VDPLOP1209RGB Mode D'emploi

Stand-Alone Mode with Built-in Program
To set the device to stand-alone mode with a built-in program:
1. Connect nothing to the DMX input [5] of the device.
2. Press <MENU> until <P--> is displayed and press <ENTER>.
3. Use <UP> and <DOWN> to select one of the built-in programs (P1 ~ P5) and press <ENTER>.
In the next step, you set the speed of the program.
4. Use <UP> and <DOWN> to set the speed of the program: adjust the duration of each step in the program
from <S--1> (short duration: fast speed) to <S100> (long duration: slow speed).
5. Press <ENTER> to confirm.
Stand-Alone Mode with Built-in Static Colour
To use one of the built-in static colours:
1. Connect nothing to the DMX input [5] of the device.
2. Press <MENU> until <C--> is displayed and press <ENTER>.
3. Use <UP> and <DOWN> to select a colour (C1 ~ C7) and press <ENTER>.
Stand-Alone Mode with Custom Static Colour
You can create a custom colour by adjusting the intensity of the red, green, and blue LEDs. Also, you can
specify a strobe rate with the custom colour.
To use a custom static colour:
1. Connect nothing to the DMX input [5] of the device.
2. Press <MENU> until <U--> is displayed and press <ENTER>.
3. Use <UP> and <DOWN> to select a colour: <r--> for red; <g--> for green, <b--> for blue, and press
<ENTER>.
4. Use <UP> and <DOWN> to set the intensity of the selected colour from 000 to 100 and press <ENTER>.
5. Repeat for all colours until you have the desired output colour.
6. To set the strobe rate, use <UP> and <DOWN> to select <S--> and press <ENTER>.
7. Use <UP> and <DOWN> to set the strobe rate (S0 ~ S20) and press <ENTER>.
7.4

Master/Slave Mode

The master/slave mode allows connecting several devices to a single master device. All slave devices will then
work synchronously with the master device.
You need to set one device to master mode and all other devices to slave mode.
Notes:
•
Configure all the slave units before connecting the master unit to the daisy chain.
•
Make sure to unplug any connection from the DMX input of the master device if you want to use it in
master/slave mode. The DMX signals from the controller may interfere with the signals from the master
device.
To set the devices to master/slave mode:
1. On each slave device, press <MENU> until <Addr> is displayed and press <ENTER>.
2. Set the DMX address to d001 and press <ENTER>.
3. Repeat for each slave device.
4. Connect the DMX input of the first slave device to the DMX output of the master device.
5. Connect the DMX input of the subsequent slave devices to the DMX output of the previous slave device.
6. Set up the master device as described in Stand-Alone Mode.
7.5 DMX Mode
This mode allows you to control the fixture by any universal DMX controller.
•
All DMX-controlled devices need a digital start address so that the correct device responds to the signals.
This digital start address is the channel number from which the device starts to "listen" to the DMX
controller. The same starting address can be used for a whole group of devices or an individual address can
be set for every device.
•
When all devices have the same address, all the units will "listen" to the control signal on one particular
channel. In other words: changing the settings of one channel will affect all devices simultaneously. If you
set individual addresses, each device will "listen" to a separate channel number. Changing the settings of
one channel will only affect the device in question.
•
In case of the 3-channel mode, you will have to set the start address of the first unit to 1 (CH1~3), the
second to 4 (1 + 3) (CH4~6), the third to 7 (4 + 3) (CH7~9), and so on. The highest start address is 510.
V. 04 – 08/01/2013
VDPLOP1209RGB
6 ©Velleman nv