Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
To make settings in a setting mode, see the corre-
sponding chapter 5.1.1 to 5.1.6.
To exit a setting mode without changing a setting,
press the button SET repeatedly until the display
briefly shows
normal mode.
5.1.1 Transmission frequency
(group / channel)
To set the transmitter quickly and easily to the
transmission frequency of the receiver unit, use the
REMOSET function (
ever, it is also possible to set the transmission fre-
quency of the transmitter manually by selecting the
channel group and the channel. The table on
page 21 gives an overview of the groups and chan-
nels.
1) Keep the button SET (4) pressed until the dis-
play briefly shows
tion (
...
mode is activated.
2) Select the group with the button – (5) or the but-
ton + (6).
3) Press the button SET to confirm. The channel
indication starts flashing on the display; the
channel setting mode is activated.
4) Select the channel with the button – or the but-
ton +.
5) Press the button SET to confirm. The display
briefly shows
the normal mode.
5.1.2 Sensitivity
For the sensitivity, several levels are available:
from 12 dB (maximum sensitivity) to -18 dB (mini-
mum sensitivity).
1) Keep the button SET (4) pressed until the dis-
play briefly shows
ting mode (group indication starts flashing).
2) Press the button SET repeatedly until the dis-
play briefly shows
sensitivity.
3) Set the sensitivity in such a way that you obtain
an optimum volume level of the microphone. If
the volume is too high, the microphone will dis-
tort; in this case, set a lower value with the but-
ton – (5). If the volume is too low, there will be a
poor signal-to-noise ratio; in this case, set a
higher value with the button + (6).
4) Press the button SET to confirm. The display
briefly shows
the normal mode.
10
. The unit will then return to the
chapter 5, step 4). How-
. Then the group indica-
)
starts flashing; the group setting
. The unit will then return to
and then the group set-
and then the current
. The unit will then return to
5.1.3 Transmission power
For the transmission power, two values are avail-
able. With a high transmission power, the range will
increase; however, the operating time of the batter-
ies will decrease due to faster discharge.
1) Keep the button SET (4) pressed until the dis-
play briefly shows
ting mode (group indication starts flashing).
2) Press the button SET repeatedly until the dis-
play shows the current transmission power:
low transmission power (10 mW)
high transmission power (50 mW)
3) Press the button – (5) to select the setting
or press the button + (6) to select the setting
.
4) Press the button SET to confirm. The display
briefly shows
the normal mode.
5.1.4 Automatic frequency matching
(REMOSET function)
To enable / disable the automatic frequency match-
ing (REMOSET function = frequency setting of the
transmitter via a radio signal of the receiver unit) for
the transmitter:
1) Keep the button SET (4) pressed until the dis-
play briefly shows
ting mode (group indication starts flashing).
2) Press the button SET repeatedly until the dis-
play shows the current setting for the automatic
frequency matching:
automatic frequency matching enabled
(i. e. frequency setting of the transmitter
via the REMOSET function is possible)
automatic frequency matching disabled
(i. e. no REMOSET transmission)
3) Press the button – (5) to select the setting
or press the button + (6) to select the set-
ting
.
4) Press the button SET to confirm. The display
briefly shows
the normal mode.
5.1.5 Identification number
To enable the REMOSET transmission between
the transmitter and the receiver unit, match their
identification numbers.
1) Keep the button SET (4) pressed until the dis-
play briefly shows
ting mode (group indication starts flashing).
and then the group set-
. The unit will then return to
and then the group set-
. The unit will then return to
and then the group set-
Publicité
Table des Matières
