Quick MINI GENIUS G 250M Manuel De L'utilisateur page 19

POS. DESCRIPTION
12 Screw M6x6
13 Anodized "MG" windlass cover
14 Screw for pressure lever
15 Spring for pressure lever "G"
16 Pressure lever "MG"
17 Sensor
18 Gasket watertight "MG"
19 Bearing 6005
20 Output gear Z88 "MG"
21 Shaft series "MG"
22 Plug 8x16
23 Long shaft series "MG"
24 Key
25 Circlip ø 25
26 Bearing
27 Gear Z56 + Z16 "MG"
28 Gear Z59+Z16 "MG"
29 Anodized windlass base "MG"
30 Screw 5x35
31 Motor
32 Screw 5x20
33 Plug 5x14
34 Plug 10x28
35 Washer 10x16
36 Roller bearing cage
37 Gear wheel Z26 "MG"
38 Gear Z16 "MG" motor shaft
39 Gasket/jig
40 Studs 8x60
41 Washer Ø8
42 Spring washer Ø8
43 Nut M8
MINI-GENIUS 250/250F - REV005A
MAINTENANCE MINI GENIUS
CODE
MBV0606MXVES
SGMSG07G0000
Quick
marine environments. In any case, any salt deposits on the outside
MSMVT07G0000
must be removed periodically to avoid corrosion and damage to
MMTND07G0000
the equipment. The parts where salt may have built up should be
PDLVTD0MG000
washed thoroughly with fresh water.
KNREEDCL0000
PGCR02MG0000
Once a year, the drum and the gypsy are to be taken apart as fol-
MBJ60052RS10
lows:
MSLRTZ881000
VERSION WITH FREEFALL SYSTEM
MSAS03120R00
Use the handle (1) to unscrew the gypsy cover (N); loosen screw (H)
MBSC00816A00
and take off the gypsy cover.
MSAS03159R00
Loosen the screws (5) of the chain stripper (7) and remove it; re-
MBH0606020X0
move the gypsy (4).
MBAE25125Y00
NO-DRUM VERSION
MBJ0608000000
Use the handle (1) to remove the gypsy cover (2); remove the top
MSLRTZ5616PR
clutch cone (3); loosen the fixing screws (5) of the chain stripper (7)
MSLRTZ5916SR
and remove it and pull off the gypsy (4).
SGMSC03MG000
MBV0535MXCE0
DRUM VERSION
EMF0212MG000
Use the handle (1) to loosen the bush (8); pull off the drum (9) and
the top clutch cone (3); loosen the fixing screws (5) of the rope/chain
MBV0520MXCE0
stripper (7) and remove it. Pull off the gypsy (4).
MBSC05014A00
MBSC01028A00
Clean all the parts removed to avoid corrosion, and grease the shaft
MBR101605000
thread (21, 23 or A) and the gypsy (4) where the clutch cones rest
MBJHK1012000
(use grease suitable for marine environment) (3).
MSLRTZ261000
Remove any oxide deposits from the terminals of the electric motor
MSLRTS151000
and the reversing contactor unit; grease them.
PGBSMG025000
MBP080608X00
MBR08X000000
MBR08XDE0000
MBD08MXEN000
WARNING: make sure the electrical power to the motor is
switched off when working manually on the windlass. Care-
fully remove the chain from the gypsy.
®
windlasses are manufactured with materials resistant to
GB
19