Setting The Dmx Start Address; Dmx Channels And Functions - IMG STAGELINE RGBL-222DMX Mode D'emploi

2) When further RGBL-222DMX panels are used,
connect the first panel via the inline jack of the
cable DMX OUT (5) to the plug (10) of the cable
DMX IN of the second panel. Proceed in the
same way to connect the second panel to the
third unit etc. until all panels have been con-
nected in a chain.
If the DMX connection cables between the
panels are too short, use suitable extension
cables (e. g. ODP-34DMX from "img Stage Line"
of 2 m length).
3) To prevent interference in signal transmission, in
case of long cables or a multitude of units con-
nected in series, terminate the DMX output of
the last DMX unit in the chain with a 120 Ω resis-
tor (> 0.3 W). The easiest way to terminate the
DMX output of an RGBL-222DMX panel is to
separate an extension cable ODP-34DMX and
to connect the resistor to the pins 2 and 3 of the
plug. Connect the plug with the resistor to the
inline jack of the cable DMX OUT.

5.3.2 Setting the DMX start address

For controlling the light effect panel with a light con-
troller, it is necessary to set the DMX start address
for the first DMX channel. If e.g. address 5 on the
DMX controller is provided for the dimmer function,
set the start address 5 on the light effect panel. The
other DMX channels of the light effect panel are
automatically assigned to the following addresses
(in this example 6 to 10). In this example, the next
possible start address for the following DMX-con-
trolled unit would be 11.
1) When the display (2) is not activated, press one
of the control buttons (3).
2) Press both control buttons A and B at the same
time so that the display starts flashing.
3) Press the button A (up) or B (down) repeatedly
until the display shows a number between 001
and 512 (see fig. 3, first line).
4) Press both control buttons A and B at the same
time again so that the display stops flashing.
5) To set the DMX start address, press the button A
or B.
Note: To indicate that the start address has been set and
DMX signals are received from the light controller, a dot
starts flashing on the display.
All rights reserved by MONACOR
be reproduced in any form or by any means for any commercial use.
® INTERNATIONAL GmbH & Co. KG. No part of this instruction manual may

5.3.3 DMX channels and functions

DMX- DMX-
channel value
1 000 – 255
2 000 – 255
3 000 – 255
4 000 – 255
000 – 007
5
008 – 255
000 – 015
016 – 031 cyan
magenta
032 – 047 magenta
048 – 063 cyan
yellow
064 – 079 cyan
magenta
080 – 095 yellow
096 – 111
112 – 127 change of colour with fade-in / fade-out effects*
6
128 – 143
144 – 159 blackout between change of colour*
160 – 175 change of colour with fade-out effects*
176 – 191 change of colour with fade-in effects*
192 – 207 change of colour with fade-in/fade-out effects*
208 – 223 crossfading between colours*
224 – 239 fast change of colour: red, green, blue*
240 – 255 fast change of colour with fade-in effects*
* The DMX channels 1 to 4 have no function here; DMX channel 5 is
used to adjust the speed.
6 Specifications
Light source: . . . . . . . . . . 12 × RGB LED, 3 W
Data protocol: . . . . . . . . . DMX 512
Number of
DMX channels: . . . . . . . . 6
Power supply: . . . . . . . . . 230 V~ / 50 Hz
Power consumption: . . . . 80 VA max.
Protection of housing: . . IP 65
Dimensions: . . . . . . . . . . 100.5 × 7.5 × 10 cm
Weight: . . . . . . . . . . . . . . 4.4 kg
Subject to technical modification.
Function
dimmer
brightness of red
brightness of green
brightness of blue
stroboscope off
stroboscope slow fast
control via channels 1 to 5
yellow blue magenta
red yellow green cyan
magenta blue magenta
red dark magenta
red dark blue magenta
stroboscope*
sudden change of colour*
(red, green, blue)
GB
*
*
*
*
*
11