Dmx Channels And Functions; Setting The Dmx Start Address; Cleaning The Spotlight - IMG STAGELINE PARC-64/CTW Mode D'emploi

5.3.1 DMX connection
GB
For DMX connection, 3-pole XLR connectors with
the following pin configuration are provided:
Pin 1 = ground, 2 = DMX-, 3 = DMX+
For connection, use special cables for DMX signal
transmission (e. g. cables of the CDMXN series
from "img Stage Line"). For cable lengths exceed-
ing 150 m, it is generally recommended to insert a
DMX level matching amplifier (e. g. SR-103DMX
from "img Stage Line").
1) Connect the DMX INPUT (4) to the DMX output
of the light controller or to the DMX output of
another DMX-controlled unit.
2) Connect the DMX OUTPUT (6) to the DMX
input of the following DMX unit. Connect the out-
put of this DMX unit to the input of the following
DMX unit etc. until all DMX-controlled units
have been connected in a chain.
3) To prevent interference in signal transmission,
in case of long cables or a multitude of units
connected in series, terminate the DMX output
of the last DMX unit in the chain with a 120 Ω
resistor (> 0.3 W): Connect a corresponding ter-
minating plug (e. g. DLT-123 from "img Stage
Line") to the DMX output jack.

5.3.2 Setting the DMX start address

For separate control of all DMX units connected to
the light controller, each unit must have its own
start address. Example: If the first DMX channel of
the spotlight is to be controlled by the DMX con-
troller via DMX address 17, set the start address on
the spotlight to 17. All other DMX channels of the
spotlight will be automatically assigned to the fol-
lowing addresses (i. e. 18 – 20 in case of start
address 17).
1) Press the button MENU repeatedly until
appears on the display.
2) Press the button ENTER. The start address
adjusted (
3) To set the desired address, press the buttons
UP and DOWN. Now the spotlight can be oper-
ated with the light controller.
Notes
1. If the DMX control does not work, call up the menu item
and press the button ENTER.
the display. If
ton UP or DOWN to switch to
2. When the menu item
on the display and DMX signals are available at the DMX
input (4), the dot at the right end of the display will flash.
All rights reserved by MONACOR
be reproduced in any form or by any means for any commercial use.
10
... ) will be indicated.
must appear on
appears on the display, use the but-
.
, , or
INTERNATIONAL GmbH & Co. KG. No part of this instruction manual may
®

5.3.3 DMX channels and functions

DMX
channel value
1 000 – 255
2 000 – 255
3 000 – 255
000 – 010
4
011 – 255
Ž
DMX channels
5.4 Temperature indication
and overheat control
The spotlight is equipped with an overheat control.
When the temperature inside the spotlight is too
high, the spotlight will be switched off. After cooling
down, the spotlight will be switched on again auto-
matically. To indicate the inside temperature:
1) Press the button MENU repeatedly until
appears on the display.
2) Press the button ENTER.
the display.
3) Press the button ENTER again. The inside tem-
perature (in °C) is indicated on the display.
4) To exit the menu branch, press the button MENU.

6 Cleaning the Spotlight

Clean the plastic filter in front of the LEDs at regu-
lar intervals or as required. This is the only way to
ensure that light will be radiated at maximum
brightness. Before cleaning, disconnect the
mains plug from the socket. Only use a dry, soft
cloth and a mild detergent. Then carefully wipe the
plastic filter dry.
For cleaning the other parts of the housing, only
use a dry, clean cloth. Never use any fluid; it may
leak into the spotlight and damage it.
7 Specifications
Data protocol: . . . . . . . . . . DMX 512
Number of DMX channels: 4
Light source: . . . . . . . . . . . white COB LED
Power consumption: . . . 100 W
Beam angle: . . . . . . . . . 60°
Colour temperature: . . . adjustable
Power supply: . . . . . . . . . . 230 V~ / 50 Hz
appears
Power consumption: . . . . . 110 VA max.
Dimensions: . . . . . . . . . . . ∅ 220 mm × 260 mm
Weight: . . . . . . . . . . . . . . . 2.9 kg
Subject to technical modification.
DMX
Function
dimmer 0 % © 100 %
basic brightness cool white
basic brightness warm white
stroboscope off
stroboscope slow © fast
2700 K – 5600 K
will appear on