Conversion For Different Gas Types; Dimensions Of The Appliance; General Appearance And Definition Of The Appliance - Candy CGG 6721 SHX Notice D'emploi Et D'installation

2.7. CONVERSION FOR DIFFERENT GAS
TYPES
For the cookers below written adjustment have to be done by qualified
technician.
Follow the steps given below to convert the appliance from the factory
set up to that for a different gas type.
Cookers are adjusted NG and connection type
is cylindric (1). For hose type NG connection,
hose adapter (2) can be fixed to cylindrical
adapter with seal.
For LPG connection, LPG hose adapter (3) can
be fixed to cylindric adapter with seal.
Adjustments and changing injectors
Changing Injectors
•Remove grates.
•Remove burner caps and burners.
•Remove injectors by using a 7 mm wrench, then screw on the correct
injector selected from gas type category table
(last 3 pages in this user manual) according to
the gas to be used.
•Follow the above steps in the reverse order
after completing the assembly of the new
injector.
Stand by Adjustment
S tand by adjustment for the cookers
without safety devices and with safety devices and button
ingition
•Turn the burner control knob to the small flame position and remove
the knob.
•If conversion from natural gas to LPG is required, turn clockwise the
by-pass screw of the gas valves with a screw driver to their final
position.
•If conversion from LPG to natural gas is required, turn anti-clockwise
the by-pass screw of the gas valves with a screw driver till a smaller
flame of ¼ size is obtained.
•After completing the adjustment, insert the knobs again.
•Check the adjustment by turning the burner control knob quickly from
maximum to minimum position. If the flame does not go out, it means
that the adjustment is correct.
•For safety devices, idle flame setting can be done with screw on valve
body. If there is ignition on the knob for idle flame setting cooktop,
toplid and panel must be removed.
•For thermostat valve idle frame setting cooktop, top lid and panel
must be removed.
By-pass screw for the burner
Gas Oven
•Remove rear cover ( Figure3)
•Remove injector adapter.(Figure 4)
•Remove injectors by using a 7 mm wrench, then screw on the correct
injector selected from gas type category table (last 3 pages in this
user manual) according to the gas to be used. (Figure 5)
•Follow the above steps in the reverse order after completing the
assembly of the new injector.
•Burner Gap is 4.5 + 0.3 mm for NG and LPG (Figure 6)
Figure3
1 2
3
without safety
devices
safety devices
Figure4
09 GB
4.5 + 0.3
Figure5

2.8. DIMENSIONS OF THE APPLIANCE

50 x 60
863
Height (mm)
510 598-600
Width (mm)
600
Depth (mm)
2.9. GENERAL APPEARANCE AND DEFINITION
OF THE APPLIANCE
This User Manual has been drawn up as a guide for several models.
Some of the properties mentioned in this manual may not exist in your
appliance.
1- Cook top
C ontrol panel
2-
3- Drawer
4- Oven door (Front door)
Glass top lid or metallic top lid
5-
6- Auxilary burner
7- Rapid burner (Semi-Rapid burner
Ultra rapid burner (Rapid burner
8-
9- Semi-Rapid burner
10- Left grate
Right grate
11-
12- Burner control knob s s
13- Thermostat oven knob
Ignition button or fan button
14-
15- Lamp knob
16- Timer knob
Moving Foot (Adjustable Feet)
17-
18- Bolt Foo t(Adjustable Feet)
1- Cook top
2- Control panel
3- Drawer
4- Oven door (Front door)
5- Metallic top lid or Glass top lid
6- Auxilary burner
7- Rapid burner (Semi-Rapid
8- Ultra rapid burner (Rapid burner
9- Hot plate
10- Left grate
11- Right grate
12- Burner control knob s s
13- Hot plate control knob
14- Thermostat oven knob
15- Ignition button or fan button
16- Signal lamp
17- Moving Foot (Adjustable Feet)
18- Bolt Foot (Adjustable Feet)
Figure6
60 x 60
850
D
600
H
W
9
10
14
)
15
)
13
12
16
burner )
)
17
18
11
17
18