Publicité
EN – Spare wheel set
The spare wheel set 57A 093 860C is intended for ŠKODA KAROQ vehicles
with 4x4 all-wheel drive with basic luggage compartment floor and standard
(i.e. fixed) rear seats as part of the equipment specification.
The spare wheel (L) itself is not included in the set. This must be ordered
from the ŠKODA Genuine Accessories range using order no. 5E3 601 011B.
Component index for the set for spare wheel:
Component
Quantity
Left-hand polystyrene box
Right-hand polystyrene box
Polystyrene spacer
Fastening bolt with knob
Luggage compartment floor pin
Plastic nut
Boot mat
Car jack
Car jack crank handle
Wheel brace
Fitting instructions
Brief description of how to insert the spare wheel and the polystyrene
toolbox into the spare wheel recess in the luggage compartment floor
(see figures).
Fig. 3 – Remove the luggage-compartment floor covering, the cover for the
rear seat attachment ridge and the tool bag from the vehicle (see
arrows).
Fig. 4 – Remove the existing cover from the spare wheel recess.
Fig. 5 – Place the polystyrene spacer (C) on the rear seat attachment ridge.
Fig. 6 – Fit the polystyrene boxes (A) and (B) (in the position shown in the
figure) onto the pins for the polystyrene spacer in the spare wheel
recess.
Fig. 7 – Secure the boxes using the plastic nuts (F).
Fig. 8 – Insert the spare wheel (L) into the spare wheel recess in the vehi-
cle's luggage compartment, with the outside of the wheel facing
downwards.
Item
1
A
1
B
1
C
1
D
1
E
4
F
1
G
1
H
1
J
1
K
1
Fig. 9 – Insert the fastening bolt with knob (D) into the opening in the spare
wheel recess. Push the bolt in and turn it 90° clockwise.
Fig. 10 – Screw on the knob as far as it will go and tighten it. Then insert
the luggage compartment floor pin (E) into the fastening bolt.
Fig. 11 – Wheel secured correctly using the luggage compartment floor pin.
Fig. 12 – Remove the equipment specification components – the towing lug,
the tool for removing the wheel covers, the plastic clip for wheel
bolt cover caps, the light bulb case, etc. – from the tool bag.
Fig. 13 – Place the car jack crank handle (J), the car jack (H), the wheel
brace (K) and the other components removed from the tool bag
into the right-hand polystyrene box (B). Place the cargo elements (if
present) into the left-hand polystyrene box (A).
Fig. 14 – Lay the mat (G) on the luggage compartment floor.
The vehicle's Owner's Manual describes in detail how to use the spare
wheel and how to replace a wheel in the event of a puncture.
CZ - Sada pro kompletní rezervní kolo
Sada pro kompletní rezervní kolo 57A 093 860C je určena pro vozy ŠKODA
KAROQ s pohonem kol 4x4 se základní podlahou zavazadlového prostoru a
standardními (tzn. pevnými) zadními sedadly ve výbavě vozu.
Rezervní kolo (L) není součástí sady. Objednejte ho ze sortimentu ŠKODA
Originální příslušenství pod objednacím číslem 5E3 601 011B.
Sada pro rezervní kolo obsahuje:
Název dílu
Polystyrenový box levý
Polystyrenový box pravý
Polystyrenová distanční podložka
Upevňovací šroub s růžicí
Podpěra podlahy zavazadlového prostoru
Plastová matice
Koberec do zavazadlového prostoru
Zvedák
Klika zvedáku
Klíč na kola
Montážní návod
Kusů
Pozice
1
A
1
B
1
C
1
D
1
E
4
F
1
G
1
H
1
J
1
K
1
7
Publicité
