Publicité
OWNER'S MANUAL | OPERATION INSTRUCTIONS
OPERATION INSTRUCTIONS
THe GAs sYsTeM
FITTINGS & HOSES
Prior to connection and use, ensure that there is no debris caught in,
or damage to, the head of the gas cylinder, regulator, hose, burner
and burner ports� (Worn or damaged hose/ regulator must be
replaced with a Blackstone approved model before using appliance�)
• Annual checking and tightening of metal fittings is recommended�
• ensure that the hose is not obstructed, kinked, or in contact with
any part of the appliance other than at its connection�
The lPG cylinder supply system must be arranged for vapor
withdrawal�
• Always keep new lPG cylinders in upright position during use,
transit or storage�
• Always keep the ventilation opening(s) of the cylinder enclosure
free and clear from debris�
If grease or other hot material drips onto valve, hose or regulator:
Turn off gas supply immediately�
STEP 01
determine the cause and correct it�
STEP 02
Clean and inspect valve, hose and regulator�
STEP 03
Perform a leak test�
STEP 04
LPG CYLINDER REQUIREMENTS
• The lP gas supply cylinder to be used must be constructed and
marked in accordance with the specifications for lP gas Cylinders
of the U�s� department of Transportation (doT) or CsA B339, as
applicable�
• only lPG cylinders marked "propane" shall be used�
• lPG cylinder must include collar to protect lPG cylinder valve�
• only use a 20 lb (9 kg) cylinder� (18 x 12 in (45 x 30 cm))
c. c.
b. b.
a. a.
THE LPG CYLINDER VALVE MUST
HAVE:
a. Type 1 valve outlet (thread on
the outside)�
b. safety relief valve�
c. Ul listed overfill Protection
device (oPd)� This oPd safety
feature is identified by a
unique triangular hand wheel�
14
CHECK SEAL BEFORE USE
The seal on the valve outlet could,
The seal on the valve outlet could,
over time, show marked and visible
over time, show marked and visible
damage or deterioration that might
damage or deterioration that might
cause a leak even with the connection
cause a leak even with the connection
tightened.
tightened.
• • A visual inspection for the seal
A visual inspection for the seal
must be carried out every time a
must be carried out every time a
lPG cylinder is replaced or refilled.
lPG cylinder is replaced or refilled.
• • Any lPG cylinder showing signs of
Any lPG cylinder showing signs of
damage or deterioration as those
damage or deterioration as those
illustrated including visible cracks
illustrated including visible cracks
and pitting, must be returned
and pitting, must be returned
unused to the seller.
unused to the seller.
REGULATOR SAFETY
• Use this appliance, as purchased, only with gas and regulator/
valve assembly supplied� do NoT use quick connect fittings or
other add-ons�
• do NoT cross thread (force at an improper angle) the connection
between your lPG cylinder and regulator�
• If you can not connect the regulator, do NoT use the regulator�
Regulator must be replaced with a Blackstone approved model by a profession-
Regulator must be replaced with a Blackstone approved model by a profession-
ally licensed, authorized dealer.
ally licensed, authorized dealer.
CoNNeCT THe lPG CYlINdeR
ensure that the control
STEP 01
knobs are turned oFF�
ensure that the lPG cylinder is
oFF by turning the hand wheel
clockwise to a full stop�
Hold the regulator in a
STEP 02
straight line with the valve outlet
so as not to cross thread the
connection�
❶ ❶ Center and insert the regu-
lator nipple into the valve outlet�
❷ ❷ Hand-tighten the coupling
nut in a clockwise direction�
(do NoT use tools to connect�)
If connection cannot be completed,
If connection cannot be completed,
disconnect regulator and repeat this
disconnect regulator and repeat this
step.
step.
The safety relief valve
STEP 03
must face away from the user
while the appliance is in use�
Connect the lPG cylinder to the
leg assembly:
❶ ❶ set the lPG cylinder on the
lPG support�
❷ ❷ Clip the lPG cylinder
retaining wire loop over the lPG
cylinder collar�
Model(s): 2357 • 2357CA
❶ ❶
❷ ❷
❶ ❶
❷ ❷
BLACKSTONE PRODUCTS
Publicité
