Publicité
English
OPERATION
WARNING: To reduce the risk of injury, ALWAYS turn
off tool and disconnect the tool from the power source
before making any adjustments or removing or installing
attachments or accessories. This applies to both the
grinder and the dust extractor vacuum. Such preventative
safety measures reduce the risk of starting the tool accidentally.
WARNING: For your own safety, read the instruction manual
for both the grinding tool and the dust extractor vacuum before
using any accessory. Failure to heed these warnings may result in
personal injury and serious damage to the tool and the accessory.
When servicing this tool, use only identical replacement parts.
nOTE: The amount of dust retained by the dust extractor
vacuum is dependent on its filter system. Refer to the dust
extractor vacuum instruction manual for more information.
1. Ensure all assembly instructions have been completed.
2. Turn the dust extractor vacuum on as instructed in the
dust extractor vacuum instruction manual.
3. Turn the tool on as instructed in the tool instruction
manual and allow it to reach full speed before making
contact with work surface.
4. Place the surface grinding shroud to flat work surface,
such as a floor or wall, and begin grinding.
5. When surface grinding is complete, turn the tool off,
allow the tool to stop rotating before laying it down and
disconnect from the power source.
nOTE: The surface grinding shroud and dust extractor
vacuum will only be effective when used with a diamond
surface cup wheel on a flat surface.
Edging Use Application (Fig. J)
This concrete grinding shroud features a hinged, edge-
grinding door to allow flush grinding against the wall.
1. Turn off the tool and disconnect from power source.
2. Open the edge grinding door
open and rest in a parked position.
3. Connect the tool to the power source.
4. Position hands and body away from wheel and door opening.
5. Place the door edge flush to the work surface before
turning the tool on and begin grinding. Remove the tool
from the work surface before turning the tool off.
6. When flush grinding is complete, turn off the tool, allow
the tool to stop rotating before pushing edge grinding
door
closed and disconnect from power source.
4
MAINTENANCE
Warning: To reduce the risk of injury, ALWAYS turn
off tool and disconnect the tool from the power source
before making any adjustments or removing or installing
attachments or accessories. This applies to both the grinder
and the dust extractor vacuum. Such preventative safety
measures reduce the risk of starting the tool accidentally.
Cleaning
WARNING: Blow dirt and dust out of all air vents with
clean, dry air at least once a week. To minimize the risk of eye
injury, always wear ANSI Z87.1 approved eye protection when
performing this procedure.
WARNING: Never use solvents or other harsh chemicals
for cleaning the non‑metallic parts of the tool. These chemicals
may weaken the plastic materials used in these parts. Use a
cloth dampened only with water and mild soap. Never let any
liquid get inside the tool; never immerse any part of the tool into
a liquid.
8
4
. The door should remain
Accessories
WARNING: The use of any accessory or attachment or
performance of any operation with this tool, other than those
recommended in this instruction manual may present a risk of
personal injury.
WARNING: Since accessories, other than those offered by
D
WALT, have not been tested with this product, use of such
e
accessories with this product could be hazardous. To reduce
the risk of injury, only D
WALT‑recommended accessories
e
should be used with this product.
Recommended accessories for use with your product are
available at extra cost from your local dealer or authorized
service center. If you need assistance in locating any
accessory, please contact D
(1-800-433-9258) or visit our website: www.dewalt.com.
Repairs
WARNING: To assure product SAFETY and RELIABILITY,
repairs, maintenance and adjustment (including brush
inspection and replacement, when applicable) should be
performed by a factory service center or an authorized service
center. Always use identical replacement parts.
Register Online
Thank you for your purchase. Register your product now for:
• WARRAnTY sERViCE: Registering your product will help
you obtain more efficient warranty service in case there is a
problem with your product.
• COnFiRMATiOn OF OWnERshiP: In case of an insurance
loss, such as fire, flood or theft, your registration of ownership
will serve as your proof of purchase.
• FOR YOUR sAFETY: Registering your product will allow
us to contact you in the unlikely event a safety notification is
required under the Federal Consumer Safety Act.
Register online at www.dewalt.com/account-login.
Three‑Year Limited Warranty
For warranty terms, go to
www.dewalt.com/support/warranty.
To request a written copy of the warranty terms, contact:
Customer Service at D
WALT Industrial Tool Co., 701 East
e
Joppa Road, Towson, MD 21286 or call 1-800-4-D
(1-800-433-9258).
lATin AMERiCA: This warranty does not apply to products
sold in Latin America. For products sold in Latin America,
see country-specific warranty information contained in
the packaging, call the local company or see website for
warranty information.
FREE WARning lABEl REPlACEMEnT: If your warning
labels become illegible or are missing, call 1-800-4-D
(1-800-433-9258) for a free replacement.
WALT. Call 1-800-4-D
WALT
e
e
WALT
e
WALT
e
Publicité
