Publicité
SETTING THE TIMER
3
1,2
2,4
B
"7"--
J--"l-j:-------!
-:.
M
/
1
2,4
1,2
6
The unit can be turned on at a specified
time every day with the
built-in
timer.
Preparation
Make sure the clock is set correctly.
(See page 6.)
1
2
3
Press the TIMER button once while pressing the
SHIFT button on the remote control to display
0, and press the I I SET button within 4 seconds.
O k
displayed,
and the hour flashes.
m
If you do not press
the
El SET button
within
4 seconds,
another
operation
may start,
Designate
the hour
of the timer-on
time
by
pressing the H
DOWN or M
UP button, and
the II SET button. Repeat to designate the minute
of the timer-on time.
After
you designate
the timer-on
time,
one of the source
names flashes
on the display
for 4 seconds.
Within
4 seconds,
press
one of the function
buttons to select a source.
The selected
source name flashes
for 4 seconds.
If this step is not completed
within 4 seconds,
repeat from
step 1.
If the TUNER/BAND
button is pressed,
the band cannot
be
selected
in this step.
4 Within
4 seconds,
select
the duration
for the
timer-activated
period with the M
DOWN or
Fl
UP button.
The duration for the timer-activated
period can be set between
5 and 240 minutes
in 5-minute
steps.
If this step is not completed
within
4 seconds,
repeat from
step 1.
5 Prepare the source.
To listen to CD, load the disc(s) to be played.
To listen to tape playback,
insert a tape into the deck.
To listen to a radio broadcast
or record it, tune in to a station.
When recording
from the tuner, insert the tape to be recorded
on into deck 1.
6 Press the POWER button to turn the unit off after
adjusting the volume and tone.
@
remains
on the display
after the power is turned
off (timer
standby
mode).
7 Get ready for the TAPE function
or the timer
recording.
To listen to the tape, press the -
button.
To record the source,
press the
button on deck 1.
When the timer-on
time is reached,
the unit turns on and begins
play or record with the selected
source.
The timer recording
period and tape length
When the length
of the tape to be recorded
is shorter
than the
timer recording
period, the
button on deck 1 is released
before
the timer is off.
When the tape length is longer than the timer recording
period,
the
button is not released.
If the
is not released
for a long
time, the tape in the deck may be damaged.
Press the WA
button to release
the
button.
To cancel the timer standby mode temporarily
While
pressing
the SHIFT
button,
press the TIMER
button
so
that @ goes out in the display.
To restore the timer standby
mode, press these buttons again to
display
0.
If using the unit after setting the timer
After setting the timer, you can use the unit. After using the unit,
check whether
the contents
in step 5 are set as you wish, turn
off the power and set step 7 if necessary.
To change the specified time and function
Repeat
all the steps again.
To check the specified
contents
While pressing
the SHIFT button,
press the TIMER
button.
The
timer-On
time,
the selected
source
name
and timer-activated
period are displayed
alternately
for 4 seconds.
m
Timer
playback
and timer
recording
will not begin
unless the
power is turned
off.
Connected
equipment
cannot be turned on and off by the built-
in timer of this unit. Use an external
timer.
17
ENGLISH
Publicité
