Publicité
Nearside (left hand side as you sit on the bike)
P
: 1
ARTS INCLUDED
ALUMINIUM BLOCK TRIANGULAR SHAPED
1
, 2 M10
AERO SHAPED SPACER
, 2
M10
LOCKING WASHER
X
RUBBER WASHERS
Remove fairing panel
Remove oil tank. Again just undo the bolts and drop it towards you to give enough room to get to bolts
Remove both of the top engine bolts
Using R&G aluminium block and the M10 x 80 socket-headed cap bolts supplied, insert M10 bolts into
aluminium block. Place 1 M10 rubber washer over each bolt and push up to block.
Fit assembly to bike and tighten.
Refit oil tank
Place left-hand side template over fairing using top two screws to locate. Hold in place with masking tape (on
outside of panel)
Mark on fairing where rough position of hole will be.
Drill pilot hole.
Carefully, using a Dremel tool or similar, cut the hole but do not go right to lines.
Offer fairing back up to bike and open hole up until it goes over the aluminium block.
When this is achieved, refit fairing.
Take one of the 12mm hex-headed bolt and place plain washer over bolt up to head of bolt then place locking
washer over bolt up to plain washer just fitted. Place bolt assembly through protector and place aero shaped spacer
over exposed end of bolt, then take the M12 rubber washer and place over bolt and push up to aero shaped spacer
just fitted.
Fit to block ensuring protector and spacer are aligned.
Tighten bolt until you feel some compression from inside the protector. Turn a little more so that you feel the
compression increase slightly. Then apply a quarter turn. Do not overtighten as damage can occur to the bike.
Fit protector cap.
IMPORTANT NOTE:
W
E WOULD ADVISE WHEN CUTTING PANELS TO WEAR A FACEMASK
CAN BE DANGEROUS TO HEALTH
Due to the risk of cross threading of bolts etc; we always recommend that our products be fitted by one of our official
dealers or a qualified mechanic.
The catalogue description and any exhibition of samples are only broad indications of the Products and R&G may make design
changes which do not diminish their performance or visual appeal and supplying them in such state shall conform to the order. The
Buyer acknowledges no representation or warranty (other than as to title) has been given or will apply to the Products other than those
in R&G's order or confirmation and the Buyer confirms it has chosen the Products as being of merchantable quality and suitable for
its particular purposes. Where R&G fits the Products or undertakes other services it shall exercise reasonable skill and care and rectify
any fault free of charge unless the workmanship has been disturbed. The Buyer is responsible for ensuring that the warranty on the
motorcycle is not affected by the fitting of the Products. On return of any defective Products R&G shall at its option either supply a
replacement or refund the purchase money but shall not be liable if the Products have been modified or used or maintained otherwise
than in accordance with R&G's or manufacturer's instructions and good engineering practice or if the defect arises from accident or
neglect. Other than identified above and subject to R&G not limiting its liability for causing death and personal injury, it shall not be
liable for indirect or consequential loss and otherwise its liability shall be limited to the amounts paid by the Buyer for the Products or
the fitting or service concerned. These terms do not affect the Buyer's statutory rights.
Returns must be pre-authorised (if not pre-authorised the return will be rejected). Goods may only be returned direct to us if they were
purchased direct from us (customer must prove if necessary). Otherwise to be returned to original vendor. Goods must be in re-
sellable condition, in the opinion of R&G Racing. All returns are subject to a 25% restocking and handling fee (25% of the gross value
exc. P&P – at the prevailing price at time of purchase). The customer must pay any and all carriage charges. No returns of
discontinued products, unless within 14 days of purchase. This policy does not affect your statutory rights and does not refer to faulty
goods.
Unit 1, Shelley's Lane, East Worldham, Alton, Hampshire, GU34 3AQ
Tel: +44 (0)1420 89007 Fax: +44 (0)1420 87301
80
-
X
SOCKET
HEADED CAP BOLTS
& 1
M12
X
RUBBER WASHER
(
RSVR
).
USED ON
PANEL
CONSUMER NOTICE
R&G RACING RETURNS POLICY (NON-FAULTY GOODS)
R&G Racing
www.rg-racing.com
, 1
AERO STYLE CRASH PROTECTOR
, 1 M12
80
-
X
HEX
HEADED BOLT
,
-
IN A WELL
VENTILATED AREA
Email:
, 1
CRASH PROTECTOR CAP
, 1 M12
, 1
WASHER
. C
ARBON FIBRE
info@rg-racing.com
,
Publicité
