Stanley FATMAX FME365 Traduction De La Notice D'instructions Originale page 6

English
(original instructions)
When assessing vibration exposure to determine safety
measures required by 2002/44/EC to protect persons
regularly using power tools in employment, an estimation of
vibration exposure should consider, the actual conditions of
use and the way the tool is used, including taking account of
all parts of the operating cycle such as the times when the tool
is switched off and when it is running idle in addition to the
trigger time.
Labels on tool
The following symbols are shown on the tool along with the
:
date code:
Warning! To reduce the risk of injury, the user
must read the instruction manual.
#
Electrical safety
This tool is double insulated; therefore no
earth wire is required. Always check that the
power supply corresponds to the voltage on the
rating plate.
● If the supply cord is damaged, it must be replaced by
the manufacturer or an authorised STANLEY FATMAX
Service Centre in order to avoid a hazard.
Using an extension cable
Always use an approved extension cable suitable for the
power input of this appliance (see technical data). The
extension cable must be suitable for outdoor use and marked
accordingly. Up to 30 m of 1.5 mm2 HO5VV-F extension cable
can be used without loss of product performance. Before use,
inspect the extension cable for signs of damage, wear and
ageing. Replace the extension cable if damaged or defective.
When using a cable reel, always unwind the cable completely.
Features
This tol includes some or all of the following features.
1. Adjustable shoe
2. Blade clamp collar
3. Pendulum selector switch
4. Variable speed on/off switch
5. Shoe release button
@
Assembly
Warning! Before attempting any of the following
operations, make sure that the tool is switched off
and unplugged and that the saw blade has stopped.
Used saw blades may be hot.
Fitting the saw blade (fig. B)
● Hold the tool away from the body
● Rotate the blade clamp collar (2).
● Insert the shank of the blade (6) fully into the blade clamp
collar (2).
● Release the blade clamp collar (2) to lock the blade
into position.
Note: The blade can be installed with the teeth up to assist in
flush cutting
6
@
Removing the saw blade (fig. B)
Warning! Burn hazard: Do not touch the blade
immediately after use. Contact with the blade may
result in personal injury.
● Rotate the blade clamp collar (2) to the release position
● Remove blade (6)
Adjustable shoe (fig. C)
The shoe (1) will adjust to limit the depth of cut.
● Press the shoe release button (5)
@
● Slide the shoe (1) to the desired position
Warning! To prevent loss of control, never use tool
without shoe.
Use
Switching on and off (fig. D)
The variable speed on/off switch offers a choice of speeds for
greatly improved cutting rates in various materials.
● To switch the tool on, squeeze the variable speed on/off
switch (4).
● To switch the tool off, release the variable speed on/off
switch (4).
Pendulum action selector (fig. E)
The FME365 has dual blade motion: straight reciprocating
motion or orbital motion.
Straight reciprocating motion is used for all metal cutting
operations and for wood cutting applications where finish is
more important than speed.
● To set the saw for straight reciprocating motion, turn the
selector to the position marked
Orbital motion is used for fast cutting of wood.
● To set the saw for orbital action, turn the selector to the
position marked .
Sawing (fig. A)
● Always hold the tool with both hands.
● Let the blade run freely for a few seconds before starting
the cut.
● Apply only a gentle pressure to the tool while performing
the cut.
● If possible, work with the shoe (1) pressed against the
workpiece. This will improve tool control and reduce
tool vibration, as well as prevent the blade from
being damaged.
Hints for optimum use
Sawing wood
● Clamp the workpiece securely and remove all nails and
metal objects.
● Holding the tool with both hands, work with the shoe (1)
pressed against the workpiece.
Flush cutting
The compact design of the reciprocating saw motor housing
and pivoting shoe permit close cutting to floors, corners and
other difficult areas.
.