Publicité
EnGLIsh
•
Check for damage to the tool, parts or accessories which may
have occurred during transport.
•
Take the time to thoroughly read and understand this manual
prior to operation.
Markings on Tool
The following pictograms are shown on the tool:
Read instruction manual before use.
Wear ear protection.
Wear eye protection.
Date Code Position (Fig. A)
The production date code
10
by a 2-digit week and is extended by a 2-digit factory code.
Description (Fig. A)
WARNING: Never modify the power tool or any part of it.
Damage or personal injury could result.
Trigger switch
1
Lock-off button
2
Blade clamp release lever
3
Shoe
4
Hand grip
5
Battery pack
6
7
Battery release button
Main handle
8
Intended Use
Your DCS380 cordless reciprocating sabre saw has been
designed for professional sawing of wood, metal and tubes. The
compact design permits cutting extremely close to the edge of
difficult areas.
DO nOT use under wet conditions or in the presence of
flammable liquids or gases.
These reciprocating saws are professional power tools.
DO nOT let children come into contact with the tool.
Supervision is required when inexperienced operators use
this tool.
Young children and the infirm. This appliance is not
•
intended for use by young children or infirm persons
without supervision.
•
This product is not intended for use by persons (including
children) suffering from diminished physical, sensory or
mental abilities; lack of experience, knowledge or skills
unless they are supervised by a person responsible for their
safety. Children should never be left alone with this product.
32
consists of a 4-digit year followed
ASSEMBLY AND ADJUSTMENTS
WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack
before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can cause injury.
WARNING: Use only D
Inserting and Removing the Battery Pack
from the Tool (Fig. F)
nOTE: Make sure your battery pack
To Install the Battery Pack into the Tool Handle
1. Align the battery pack with the rails inside the tool's
handle (Fig. F).
2. Slide it into the handle until the battery pack is firmly seated
in the tool and ensure that you hear the lock snap into place.
To Remove the Battery Pack from the Tool
1. Press the battery release button
battery pack out of the tool handle.
2. Insert battery pack into the charger as described in the
charger section of this manual.
Fuel Gauge Battery Packs (Fig. B)
Some D
WALT battery packs include a fuel gauge, which
e
consists of three green LED lights that indicate the level of
charge remaining in the battery pack.
To actuate the fuel gauge, press and hold the fuel gauge
button
9
. A combination of the three green LED lights will
illuminate, designating the level of charge left. When the level
of charge in the battery is below the usable limit, the fuel gauge
will not illuminate and the battery will need to be recharged.
nOTE: The fuel gauge is only an indication of the charge left on
the battery pack. It does not indicate tool functionality and is
subject to variation based on product components, temperature
and end-user application.
Blade Installation and Removal
(Fig. A, E–G, J)
Different blade lengths are available. Use the appropriate blade
for the application. The blade should be longer than 89 mm and
should extend past the shoe and the thickness of the workpiece
during the cut. Do not use jigsaw blades with this tool.
WARNING: Cut hazard. Blade breakage may occur if the
blade does not extend past the shoe and the workpiece
during the cut (Fig. E). Increased risk of personal injury, as
well as damage to the shoe and workpiece may result.
To install blade into saw
1. Pull blade clamp release lever
2. Insert blade shank from the front.
3. Push blade clamp release lever down.
nOTE: The blade can be installed in four positions as shown in
Figure F. Both units allow the blade to be installed upside-down
to assist in flush-to cutting; see Figure J.
WALT batteries and chargers.
e
6
is fully charged.
7
and firmly pull the
3
up (Fig. A).
Publicité
