Publicité
Keep the instructions for future.
NF-EN-71
Warning! Protective equipment should be worn. Not to be used
in traffic.
20 kg max.: Seat mode (ride-on, walking bike)
50 kg max.: Scooter mode
Seat mode: Warning! Not to be used by children over 36 months due
to the limited strength of the seat bracket frame. The seat can only
be used with this product when the steering is completely locked by
the parents using the locking button located at the upper side of the
steering assembly. Press down the locking button in order to lock the
steering of the wheels when the seat is to be mounted.
Remove the scooter and all the parts from the box. Set out all the
parts and read the assembly instructions prior to use. Keep the
packaging until assembly is complete.
General instructions
This toy must be assembled by a responsible adult. Prior to use, make
sure that the toy has been assembled properly. Remove all the parts
which are not necessary for play before giving the toy to your child.
The toy should be used with caution since skill is required to avoid
falls or collisions causing injury to the user or third parties.
To use with suitable protective equipment, including a helmet, shoes,
elbow, wrist and knee protectors. Teach the child how to use it safely
and responsibly.
Directions:
- T he scooter can be dangerous and can cause traffic accidents when
used on public highways. Don't use on public roads. It is best used
on a flat, clean surface, free of gravel and grease. Avoid bumps and
drainage grates that may cause an accident.
- T he scooter does not include any headlights or lights. It is therefore
not suited for use at night or during periods when visibility is limited.
- A lways use under adult supervision.
- Do not allow more than one child to ride the scooter at the same
time.
- Do not use on wet days, or on wet ground.
8
Before and after use:
- Make sure that all locking mechanisms are securely locked.
- C heck the height of the steering system, and make sure the nuts
are tightened and that the handlebars and the front wheel are
perpendicular.
- T he minimum height of T-bar has to be locked at the lowest position
by switching the bullet into the lowest hole (see diagram A).
- C heck all of the connection elements: the brake, the steering
column's quick release system and the wheel axles must be adjusted
correctly and not damaged.
- Also check the tyre wear.
INSTALLATION AND USE OF SEAT FOR USE (See page 2)
• GO•UP DELUXE LIGHTS 360° SERIES comes with a sturdy seat
support frame to better distribute the load of the seated child. There
are 3 different seat heights available: 27 - 31cm. For a comfortable
ride, your child's feet should easily touch the footrest and the
ground.
• Place the footrest under the seat support bar in the correct direction
(see diagram 1). Make sure the spring ball on the side "click" into
place.
• Insert the seat support bar into the integrated tube at the front of the
scooter deck between the two front wheels. Make sure the spring
ball on the side at the bottom of the column "click" into place to
securely hold the seat frame. (see diagram 2-3)
• Attach the seat to the seat support bar by slotting in from the top, a
guided track can be found. Go all the way down to get the suitable
seat height with engraved 1/2/3, then tighten the knob to make sure
it is securely fixed.
• Warning! Exert all your strength on the seat to check seat support
bar is locked in the place safely before riding.
Ride-on mode:
• Insert the handlebar tube in the back hole of the seat support frame.
Align the spring-loaded buttons with the notches in the seat support
frame and lock (Figure 4). Double check that the spring-loaded
button is engaged and locked correctly.
• Adjus
posit
clam
clam
• The p
use.
the fo
• Insta
scoo
safet
• The p
guide
the a
• Warn
child
hand
• Warn
modu
Walkin
• Rem
frame
• GO•U
adjus
posit
heigh
frame
• Warn
the s
Steerin
while th
first.
Publicité
