Publicité
process. On the upper screw of the brake course, you can adjust the brake again (4d).
5. BRAKE (fig. 5)
Press the rear brake down by foot to stop the rear wheels and push the stroller to check.
Attention: Always apply both brakes when parking the stroller.
6. ADJUSTING THE BACK REST (fig. 6a-6b)
The back rest is adjusted via the pull belt with clasp which is located at the rear part of the seat
upholstery. This enables the inclination of the back rest to be individually adjusted. Pull the belt
while holding the clasp to set the seat in sitting position. Press the button on the clasp and pull
the clasp down to release the seat to lying position.
7. ADJUSTING THE LEG REST (fig. 7)
Press both (left & right) buttons to bring the leg rest to the desired position.
8. ADJUSTING THE HANDLES (fig. 8)
Press both (left & right) buttons on the handle and bring the handle height to the desired
position.
9. INSTALL THE FRONT BAR (fig. 9a, 9b)
Install the front bar just below the locking latches by pushing in the front bar into the housings
(9a). You will hear a click sound when they are secured onto the frame. Test the front bar by
pulling on it to make sure it is locked into place. To release the front bar, push the buttons
underneath and pull out the front bar (9b).
10. ASSEMBLE THE CANOPY (fig. 10)
Slide the canopy plastic housings on the catches above the locking latch on each side.
11. FOLDING AWAY (fig. 11):
Make sure the backrest is always in a recline position. Fold the canopy backward. Pull the
release levers on the right and left up at the same time. Press the handle down and fold the
stroller together. Close the transport lock on the side of the frame.
12. CHECKING THE PRESSURE OF AIR WHEEL
You can pump up the pneumatic tires with the tire pump provided. The tire pressure must not
exceed 2.0 bar (28PSI).
13. SECURE THE CHILD IN THE SEAT (fig. 12):
Place the child in the seat and push the clips on the waist belt into the buckle on the crotch belt
(the one that comes between the child's legs). Adjust the length of the belt to your child's needs.
Always ensure the straps are not twisted or caught on the stroller frame. Check the adjustment
every time you place the child in the seat and when the backrest is reclined. To release the
harness, squeeze & open the buckle.
Harness adjustment: Insert both fasteners (B) into the buckle (A), ensure that both buttons click
into position. Ensure both shoulder straps (C) are attached to the fasteners (B). Each strap has
its own length adjuster (D). To undo the harness, press the buttons and pull apart. "D" Rings
are provided for fitment of a full safety harness. The attachment points (D-rings) are located
on side straps.
WARNING: (A child's safety is your responsibility.) The child should be harnessed in at all times
and should never be left unattended. The child should be clear of moving parts while making
adjustments. This stroller requires regular maintenance by the user.
Attention: Avoid serious injury from failing and sliding out, always use seat belt & always use
as instructed. Never use the harness without the shoulder straps.
OPTION FEATURES – SHOP N DRIVE TRAVEL SYSTEM:
This stroller is able to adapt our Hauck Zero Plus® Infant Carseat as a Travel System. To adapt the
carseat, please follow the following steps:
A. There is an adaptor clip on the each side of the stroller's folding plastic, pull both of them up.
(figure A).
B. Release the stroller seat to the lowest recline position. Place the Zero Plus® Infant Carseat on
top of the stroller's front bar. (figure B).
C. Push the Zero Plus® Infant Carseat down until you hear the clip sound on both left & right sides
(figure C1, C2). Lift up carefully the carseat to check if the carseat is securely locked in place.
D. To release the carseat, push up the left & right levers, which are located underneath the carseat,
and the adaptors can be released. (figure D1). Then lift up the carseat carefully (figure D2), and
close the adaptors back to the original housing (figure D3).
GB
9
Publicité
