Further Safety Instructions - Festool TSC 55 KEB Notice D'utilisation D'origine

Masquer les pouces Voir aussi pour TSC 55 KEB:

Notice d'utilisation d'origine (94 pages)

Notice d'utilisation (61 pages)

Table des Matières

Les langues disponibles

Lower guard function

Check the lower guard for proper closing

–

before each use. Do not operate the saw if

the lower guard does not move freely and

close instantly. Never clamp or tie the

lower guard into the open position. If the

saw is accidentally dropped, the lower

guard may be bent. Raise the lower guard

with the retracting handle and make sure it

moves freely and does not touch the blade

or any other part, in all angles and depths

of cut.

Check the operation and condition of the

–

guard return spring. If the guard and the

spring are not operating properly, they

must be serviced before use. The guard

may operate sluggishly due to damaged

parts, gummy deposits, or a build-up of de

bris.

Assure that the base plate of the saw will

–

not shift while performing a "plunge cut".

Blade shifting sideways will cause binding

and likely kick back.

Always observe that the guard is covering

–

the blade before placing the saw down on

bench or floor. An unprotected, coasting

blade will cause the saw to walk back

wards, cutting whatever is in its path. Be

aware of the time it takes for the blade to

stop after the switch is released.

Function of the feeler wedge [1-21] (kickback

stop function)

Every time the saw blade is replaced,

–

clean the feeler unit [5-4] by blowing it out

or using a brush. Any contamination of the

feeler unit may impair the kickback stop

function and therefore prevent the saw

blade from being stopped.

Do not operate the saw if the feeler wedge

–

is bent. Even the slightest damage can

slow the braking of the saw blade.

3.3

Safety instructions for the pre-

assembled saw blade

Usage

–

The maximum speed specified on the saw

blade must not be exceeded and the speed

range must be adhered to.

–

The pre-installed saw blade is only de

signed for use in circular saws.

–

Proceed with extreme care when unpack

ing, packing and handling the tool (e.g. in

stalling it in the machine). There is a risk of

injury from extremely sharp cutting edges!

–

When handling the tool, wearing safety

gloves provides a more secure hold of the

tool and further reduces the risk of injury.

–

Circular saw blades with cracked bodies

must be replaced. Repair is not permitted.

–

Circular saw blades with a combination de

sign (soldered saw teeth) with saw tooth

thickness smaller than 1 mm must no lon

ger be used.

–

Do not use tools with visible cracks or blunt

or damaged cutting edges.

Installation and mounting

–

Tools must be clamped in such a way that

they cannot come loose during operation.

–

When assembling the tools, it must be en

sured that the clamping takes place on the

tool hub or the clamping surface of the

tool, and that the cutting edges do not

come into contact with other components.

–

Do not lengthen the key or tighten by hitting

with a hammer.

–

The clamping surfaces must be cleaned to

remove contamination, grease, oil and wa

ter.

–

Clamping screws must be tightened ac

cording to the manufacturer's instructions.

–

Only securely installed rings, e.g. rings that

have been pressed in or those that are held

in position by an adhesive bond, may be

used to adjust the hole diameter of circular

saw blades to the spindle diameter of the

machine. The use of loose rings is not per

mitted.

Service and maintenance

–

Repairs and sanding work may only be car

ried out by Festool customer service work

shops or experts.

–

The tool design must not be changed.

–

Deresinify and clean the tool regularly

(cleaning agent with pH between 4.5 and 8).

–

Blunt edges can be resharpened on the

clamping surface to a minimum cutting

edge thickness of 1 mm.

–

Only transport the tool in suitable packag

ing – risk of injury!

3.4