Publicité
EN
ORIGINAL INSTRUCTIONS
Safety, performance, and dependability have been given top
priority in the design of your battery charger.
INTENDED USE
The charger is intended only to recharge the compatible
battery packs listed in this manual.
The product is only for indoor use, in dry conditions.
The product is not intended to recharge any other type of
battery or be used as a power supply. It should never be
used in explosive or fl ammable environments.
Do not use the product for any other purpose.
CHARGER SAFETY WARNINGS
■
Read all safety warnings and all instructions. Failure to
follow the warnings and instructions may result in electric
shock, fire, and/or serious injury. Save all warnings and
instructions for future reference.
■
Do not recharge primary cells (non-rechargeable).
■
The product must not be damp and should never be
used in a damp environment.
■
The product is for indoor use only.
■
Do not cover any ventilation slots, and provide adequate
ventilation during operation.
■
The power supply voltage must correspond with the
voltage specifications on the product.
■
Before using the product, check that the charger
enclosure, cable, and plug are not damaged. If damage
is found, do not use the product and bring it to an
authorised service centre for repair.
■
Do not use the product if it has suffered any heavy shock
or jolting, or if it is damaged in any other way.
■
When charging, do not expose the product to sunlight
or other heat source. The recommended temperature
range at the charging vicinity is 10 °C to 25 °C.
■
Due to the heat generated during charging, do not use
the product on a combustible surface.
■
Do not use the product near flammable materials,
such as cloth, packaging materials, paint, spray paint
or aerosols, lubricants, thinners, petrol containers, gas
containers, or gas appliances.
■
Never modify, disassemble, or attempt to repair the
product yourself.
■
Do not allow the charger or battery packs to become
contaminated with any material that could be conductive,
such as metallic particles from grinding, cutting, or
machining processes.
■
Protect the battery contact terminals from metallic
objects to avoid a short circuit, which can cause fire or
explosion.
■
Unplug the product from the power socket when it is not
in use or when cleaning it.
■
Use only an extension cable that is approved and in
good condition.
■
Do not charge battery packs that show signs of leaks.
Dispose of them properly.
■
Never charge a damaged battery pack. Replace
damaged battery packs immediately.
■
Before every use, examine the power cord for damage.
If the power cord is damaged, it must be replaced by a
qualified person at an authorised service centre to avoid
a hazard.
■
The product should only be used on flat, level, stable
surfaces. Do not pull at cords that can cause the product
to tip over.
ADDITIONAL BATTERY SAFETY WARNINGS
To reduce the risk of fi re, personal injury, and product
damage due to a short circuit, never immerse the tool,
battery pack, or charger in fl uid or allow fl uid to fl ow inside
them. Corrosive or conductive fl uids, such as seawater,
certain industrial chemicals, and bleach or bleach-containing
products, etc., can cause a short circuit.
WALL MOUNTING
See Fig. 5.
■
Carefully select a stable wall for mounting the charger.
Make sure that there is no hindrance to mounting work
or operation. The maximum gross weight of the charger
is approximately 4.8 kg, provide sufficient reinforcement
for the wall if necessary.
■
Mount the charger in a vertical orientation only. Install
two screws on the wall to mount the charger. Otherwise,
the charger may fall and cause serious injury.
■
Check the tightness of the screws on a regular basis.
Make sure that the head of the screws fit properly in
the wall mounting holes to hold the charger firmly in
place. Otherwise, the charger may fall because of loose
screws.
OPERATION
CHARGING THE BATTERY PACK
■
Battery packs are shipped in a low charge condition.
Therefore, you should charge them before first use.
If the charger does not charge the battery pack under
normal circumstances, bring both the battery pack and
charger to an authorised service centre.
■
Make sure that the power supply is normal household
voltage, 220–240 V, 50/60 Hz, AC only.
■
Make sure that the battery pack latch clicks into place
and that the battery pack is secured in the charger
before charging.
■
Do not place the charger and battery pack in an area of
extreme heat or cold. They work best at normal room
temperature.
NOTE: When charging, the charger and battery pack should
be placed in a location where the temperature is more than
10 °C but less than 38 °C.
EN
FR
DE
ES
IT
NL
PT
DA
SV
FI
NO
RU
PL
CS
HU
RO
LV
LT
ET
HR
SL
SK
BG
UK
TR
EL
3
Publicité
