Publicité
EN
Note:
• Rinse the filter grid with clean water and do not add
any detergent.
• Do not clean the filter grid with a brush or your fingers.
• Allow the filter grid to air dry for at least 24 hours.
Wiping module (clean after each use)
1. Remove and clean the cloth.
2. Wipe the water tank dry.
Sensors (clean regularly)
Clean the sensors with a soft cloth as follows:
1. Keep the robot switched off during cleaning. Clean
the side sensor, fall sensors, charging contacts at the
bottom of the robot and other sensors shown in the
picture.
2. Unplug the docking station from the electrical supply
and wipe the charging contacts on the docking station.
Anti-fall sensor
Charging
contact
Side sensor
82
Sensors (clean every month)
LDS laser range-
finder
Anti-collision sensor
for radar sensor
Anti-collision
sensor
Infra-red
charging sensor
Battery
• The appliance is equipped with high-performance
lithium-ion
batteries.
To
maintain
battery
performance, keep the appliance charged every day.
• If the appliance is not used for a long time, turn it off
and store it properly. Charge it at least every 3 months
to prevent damage to the battery due to excessive
discharge.
Firmware update
Use the mobile app to update the firmware. If new
firmware is detected, update as prompted. When
updating the firmware, the battery level should be ≥50 %
and the appliance must be placed in the docking station.
Docking station
• Do not use without dust bag and coarse filter.
• Check the status of the bag in the docking station.
If the bag is full, replace it with a new one.
• Clean the charging contacts and the suction opening.
• Remove the coarse filter of the docking station and
rinse it with water. Allow to dry properly and put back.
COMMON PROBLEMS
Problem
The robot cannot be
• If the battery is low, place the robot in the docking station and align it with the
started
board contacts, the appliance will start automatically (if the robot is completely off,
it can start automatically after a while).
• Do not use the appliance if the ambient temperature is below 0 °C or above 40 °C.
The robot cannot be
• Move the robot away from the docking station and check that the docking station
charged
power cable is properly connected to the power supply.
• In case of poor contact, clean the docking station contact points and charging
contacts on the robot.
The robot cannot be
The robot is too far from the docking station, place it near the docking station and try
recharged
again.
Abnormal behaviour
Turn off the robot and restart it.
Unusual noise is heard
The main brush, side brush or wheel may be wrapped with foreign objects, turn off the
during use
robot and remove foreign objects.
Cleaning ability is
• The dust container is full. Clean it.
reduced or dust is
• The filter is clogged. Clean it or replace it.
dropping from the
• The main brush is wrapped with foreign objects, clean it.
appliance
Wi-Fi cannot be
• The Wi-Fi signal is bad. Check that the correct Wi-Fi coverage is available.
connected
• Wi-Fi is connected in an unusual way. Reset Wi-Fi, download the latest app, and try
connecting again.
• The password is entered incorrectly.
• There is a router for the 5GHz frequency band, the robotic vacuum cleaner is
equipped only for the 2.4GHz frequency band.
The planned cleaning did
If the battery level is low, planned cleaning can only be started if the battery level is
not take place
at least 30 %.
Does the robot consume
The robot consumes a small amount of power when it is permanently placed in the
power when it is always
docking station, allowing the best battery performance.
placed in the docking
station?
Does the robot need to
The lithium battery can be used immediately after charging and has no memory effect.
be charged for 16 hours
for the first 3 uses?
TROUBLESHOOTING
Voice message
Error 1: Oh dear! I cannot find the dust collector
Error 2: Please check if the radar on top has been covered
or blocked
Error 3: Please place me in a new location and try again
EN
Remedy
Problem
Cleaning was started after removing the dust container.
The top sensor is covered or placed in an open area
(there is no obstruction in the 6x6 m
2
area).
Pick up the robot or lift it into the air.
83
Publicité
