Publicité
EN
CLEANING/PAUSE
After starting the appliance, briefly press the button
on the appliance or start the appliance using the mobile
app or remote control (press any button to pause the
appliance).
CHARGING
Automatic mode: After completing the cleaning, the
device automatically returns to the docking station,
where the dirt is sucked out of the container.
Manual mode: When paused, press the button
briefly to start charging or you can charge the device by
controlling it with the mobile app or remote control.
Note: If the appliance does not find the docking station,
it will automatically return to its original position. In this
case, place the device manually into the docking station.
COMPLETE AUTOMATIC CLEANING
Once the robot is on, it performs a search, generates a map
and intelligently divides it into areas. It then thoroughly
vacuums the areas one by one along the wall and plans
the cleaning path in curves / S-shapes. After cleaning, the
robot automatically returns to the charging base.
Note: Do not move the robot arbitrarily and often during
cleaning. After moving, place the robot in its original
position. When the robot is on again, it will try to take
a position itself. After successful positioning, the robot
will follow the planned path and continue working. If
positioning fails, the robot cancels the previous task,
creates a map, and cleans up again. Even if it does not find
a charging base.
LOCAL CLEANING VIA APP
If a local area needs more thorough cleaning, the user
specifies an area of 1.5 x 1.5 m that he/she wants to clean
on the map. The appliance automatically moves to this
area and starts cleaning it.
LOCAL CLEANING WITHOUT APP
If you cannot control the robot using the mobile app,
move the robot manually to the place you want to clean
up. Press the button
for 5 seconds and the robot will
perform double cleaning in the area of 1.8 x 1.8 m with
the centre in its starting position.
ZONE CLEANING
Use the mobile app to set the size and location of the area
you want to clean up. You can set up to 5 areas. The robot
will clean in the areas you have set.
ROOM CLEANING
Use the mobile app to select the rooms you want to clean.
80
RESTRICTED ZONE
Use the mobile app to set up one or more restricted
areas. The robot will not clean in these restricted areas
and will clean in others.
Note: The robot may reach the restricted area due to
positioning errors, sensor errors or other reasons.
• A permanently restricted zone may be invalidated
due to a significant change in position of the charging
base and furniture. Therefore, try not to move the
robot or otherwise interfere with its work during
cleaning.
• The permanently restricted area will be revoked as
soon as the map is restored.
NO WIPING ZONE
Use the mobile app to select a no wiping zone. If the robot
is equipped with a wiping module, it will not go to this
area. If the appliance only vacuums, it will go to this area.
CLEANING PLANNING
You can set a fixed cleaning time using the mobile app.
The robot will automatically start cleaning at the set time
and return to the docking station when finished.
WI-FI RESET
If the mobile phone cannot connect to the appliance
due to a change in router and password configuration or
other reasons, press the button
and the button
seconds until the beep sounds and the icons turn orange.
Follow the instructions in the app to reconnect.
SILENT MODE
You can activate silent mode in the app or with the remote
control. The robot's voice messages and scheduled
cleaning will be suppressed (inactive) during the set time.
Cleaning can be started manually.
AUTO BOOST
When the carpet is detected, the suction force
automatically increases to the highest level.
SETTING THE SUCTION POWER
You can switch off or adjust the suction power using the
mobile app or remote control.
WATER FLOW SETTING
You can adjust the water flow using the mobile app or the
remote control.
USING THE REMOTE CONTROL
1. Automatic cleaning/pause
2. Forward movement
3. Left turn
4. Suction power adjustment
5. Quiet mode
6. Switching the button illumination off/on
7. Start/stop charging
8. Turn right
9. Find the robot
10. Adjusting water flow rates
11. Local cleaning
1
2
3
4
5
for 3
6
Note: To ensure that all the correct settings are effective,
you must point the remote control at the front of the
robotic vacuum cleaner from close proximity.
DAILY MAINTENANCE
Main brush (clean regularly)
1. Turn the appliance over and press the latch on the
main brush cover to pull it out.
2. Remove dust from inside and from inside the main
brush with a small brush and clean the main brush.
3. Reassemble the main brush and press firmly on the
cover until the latch clicks into place.
Side brushes (clean regularly)
1. Turn the robot over and pull the side brushes upwards.
2. Remove the hair and dirt and put the side brushes back
7
on by pushing them in. Make sure the left side brush (L)
and the right side brush (R) match the L and R symbols
on the bottom cover of the vacuum cleaner.
8
Note: It is recommended to change the side brushes
every 3-6 months to ensure their cleaning effect.
9
Dust container and filter grid (clean regularly)
1. Press the button and pull the dust container
10
backwards.
2. Open and clean the dust container.
Cleaning the filter grid (clean regularly)
11
1. After prolonged use, remove the HEPA filter and the
foam filter.
2. Rinse the filters with clean water.
3. Wipe the individual parts and let them air dry.
4. After drying, assemble them in the correct order:
grid - foam filter - HEPA filter.
EN
81
Publicité
