Declaration Of Conformity; Battery Charging - Bosch GGS 18 V-LI Professional Notice Originale

OBJ_BUCH-1461-001.book Page 14 Thursday, May 19, 2011 4:57 PM
14 | English
Straight grinder
Grinding tool diameter, max.
Weight according to
EPTA-Procedure 01/2003
Please observe the article number on the type plate of your machine.
The trade names of the individual machines may vary.

Declaration of Conformity

We declare under our sole responsibility that the product de-
scribed under "Technical Data" is in conformity with the fol-
lowing standards or standardization documents: EN 60745
according to the provisions of the directives 2004/108/EC,
2006/42/EC.
Technical file at:
Robert Bosch GmbH, Postfach 10 01 56,
D-70745 Leinfelden-Echterdingen
Dr. Egbert Schneider Dr. Eckerhard Strötgen
Senior Vice President Head of Product
Engineering Certification
Robert Bosch GmbH, Power Tools Division
D-70745 Leinfelden-Echterdingen
04.04.2011
Assembly

Battery Charging

Use only the battery chargers listed on the accessories
page. Only these battery chargers are matched to the lith-
ium ion battery of your power tool.
Note: The battery is supplied partially charged. To ensure full
capacity of the battery, completely charge the battery in the
battery charger before using your power tool for the first time.
The lithium-ion battery can be charged at any time without re-
ducing its service life. Interrupting the charging procedure
does not damage the battery.
The lithium-ion battery is protected against deep discharging
by the "Electronic Cell Protection (ECP)". When the battery is
empty, the machine is switched off by means of a protective
circuit: The inserted tool no longer rotates.
Do not continue to press the On/Off
WARNING
switch after the machine has been au-
tomatically switched off. The battery can be damaged.
The battery is equipped with a NTC temperature control
which allows charging only within a temperature range of be-
tween 0 °C and 45 °C. A long battery service life is achieved
in this manner.
Observe the notes for disposal.
3 609 929 C07 | (19.5.11)
Removing the Battery
GGS 18 V-LI
The battery 7 is equipped with two locking levels that should
Professional
prevent the battery from falling out when pushing the battery
mm 50
unlocking button 6 unintentionally. As long as the battery is
inserted in the power tool, it is held in position by means of a
kg 1.8
spring.
To remove the battery 7, press the battery unlocking button 6
and pull the battery upward out of the power tool. Do not ex-
ert any force.
Battery Charge-control Indication (only for 3,0 Ah bat-
tery) (see figure A)
The three green LEDs of the battery charge-control indicator
10 indicate the charge condition of the battery 7. For safety
reasons, it is only possible to check the status of the charge
condition when the machine is at a standstill.
Press button 9 to indicate the charge condition. This is also
possible when the battery 7 is removed.
LED
Continuous lighting 3 x green
Continuous lighting 2 x green
Continuous lighting 1 x green
Flashing light 1 x green
When no LED lights up after pushing button 9, then the bat-
tery is defective and must be replaced.
Mounting the Grinding Tools (see figure B)
Before any work on the machine itself (e. g. mainte-
nance, tool change, etc.) as well as during transport
and storage, remove the battery from the power tool.
There is danger of injury when unintentionally actuating
the On/Off switch.
Only use properly fitting and undamaged open-end
spanners (see "Technical Data").
– Clean the grinder spindle 3 and all parts to be mounted.
– Hold the grinder spindle 3 with open-end spanner 11 by
the spanner flats.
Loosen the clamping nut 2 with open-end spanner 12 by
applying it to the spanner flats and turning in anticlockwise
direction.
– Insert the clamping shaft of the grinding tool to the stop in-
to the collet chuck 1.
– Hold the grinder spindle 3 firmly with open-end spanner
11 and clamp the tool bit with open-end spanner 12 by the
spanner flats, turning in clockwise direction.
Capacity
≥2/3
≥1/3
<1/3
Reserve
Bosch Power Tools