Publicité
10 | English
Removing the Battery
To remove the rechargeable battery, press the battery re-
lease button and pull the battery out. Do not use force to do
this.
The rechargeable battery has two locking levels to prevent
the battery from falling out if the battery release button is
pressed unintentionally. The rechargeable battery is held in
place by a spring when fitted in the power tool.
Battery charge indicator
Note: Not all battery types have a battery charge indicator.
The green LEDs on the battery charge indicator indicate the
state of charge of the battery. For safety reasons, it is only
possible to check the state of charge when the power tool is
not in operation.
Press the button for the battery charge indicator or
show the state of charge. This is also possible when the bat-
tery is removed.
If no LED lights up after pressing the button for the battery
charge indicator, then the battery is defective and must be
replaced.
Battery model GBA 18V...
LED
3× continuous green light
2× continuous green light
1× continuous green light
1× flashing green light
Battery model ProCORE18V...
LED
5 × continuous green light
4 × continuous green light
3 × continuous green light
2 × continuous green light
1 × continuous green light
1 × flashing green light
Recommendations for Optimal Handling of the
Battery
Protect the battery against moisture and water.
Only store the battery within a temperature range of −20 to
50 °C. Do not leave the battery in your car in the summer, for
example.
Occasionally clean the ventilation slots on the battery using a
soft brush that is clean and dry.
A significantly reduced operating time after charging indic-
ates that the battery has deteriorated and must be replaced.
1 609 92A 93K | (05.09.2024)
Follow the instructions on correct disposal.
Assembly
Before carrying out any work on the power tool (e.g.
u
maintenance, tool change etc.), remove the battery
from the power tool. There is risk of injury from uninten-
tionally pressing the on/off switch.
Changing the tool
Before carrying out any work on the power tool (e.g.
u
maintenance, tool change etc.), remove the battery
from the power tool. There is risk of injury from uninten-
tionally pressing the on/off switch.
Inserting the application tool: ISR 18V-30 PHX (see
figure B)
to
Pull the locking sleeve (3) back, guide the application tool
into the tool holder (1) as far as it will go and release the
locking sleeve (3) to lock the application tool.
Please note that the locking interface is optimized for
the most commonly used application tool dimension in
the individual country of use.
Inserting the application tool: ISR 18V-30 P (see
figure A)
Open the keyless chuck (2) by turning it in the direction of
Capacity
rotation ➊ until the tool can be inserted. Insert the tool.
60–100 %
Firmly tighten the keyless chuck (2) by turning it by hand in
the direction of rotation ➋. This will automatically lock the
30–60 %
drill chuck.
5–30 %
The lock will disengage again if you turn the sleeve in the op-
0–5 %
posite direction to remove the tool.
Removing the application tool: ISR 18V-30 PHX
Pull the locking sleeve (3) back and pull the application tool
out of the holder (1).
Dust/Chip Extraction
Capacity
Dust from materials such as lead-containing coatings, some
80–100 %
wood types, minerals and metal can be harmful to one's
health. Touching or breathing-in the dust can cause allergic
60–80 %
reactions and/or lead to respiratory infections of the user or
40–60 %
bystanders.
20–40 %
Certain dust, such as oak or beech dust, is considered carci-
5–20 %
nogenic, especially in connection with wood-treatment ad-
ditives (chromate, wood preservative). Materials containing
0–5 %
asbestos may only be worked by specialists.
– Provide for good ventilation of the working place.
– It is recommended to wear a P2 filter-class respirator.
Observe the relevant regulations in your country for the ma-
terials to be worked.
Avoid dust accumulation at the workplace. Dust can
u
easily ignite.
Bosch Power Tools
Publicité
