Publicité
One-year standard tool warranty
Should your Tacwise air tool become defective due to faulty materials or workmanship within 12 months from the date of purchase, we guarantee to replace all
defective parts free of charge or at our discretion, replace the tool entirely. However, this one-year warranty does not cover any consumable parts such as
drivers, O-rings, springs etc.
6-month standard consumable parts warranty
Tacwise air tools are warranted to be free from defects with all its original consumable parts for 6-months from the date of purchase.
Neither of these warranties cover:
• Tools that have received unauthorised changes or additions.
• Defects caused by using accessories, components or spare parts other than approved/genuine Tacwise accessories or parts.
• Component parts that are subject to natural wear and tear caused by use in accordance with our operating instructions.
• Defects to the tool caused by improper use, abnormal environmental conditions or inappropriate operating conditions, non-compliance with our operating
instructions or insufficient servicing or maintenance.
• Proof of purchase must be produced with an original receipt.
Operating Instructions
Technical data
Characteristics
Model
Nail type
Nail length range
Magazine capacity
Minimum operating air pressure
Maximum operating air pressure
Air inlet
Air consumption
Weight
Vibration emission level*
* The declared vibration emission level represents the main applications of the tool. However if the tool is used for different applications, with different
accessories or poorly maintained, the vibration emission may differ. This may significantly increase exposure level over the total working period.
CE – Declaration of Conformity
KDH90V
Tacwise declares that this power tool has been designed in compliance with the Regulations and Standards of the European Directives.
Quality Department, Tacwise Group Plc – UK
Features (Fig. A)
1. Trigger
2. Firing mode selector
3. Quick-release plug (Euro fitting)
4. Feeder
5. Magazine
6. Non-marking nose
7. Depth adjustment wheel
8. Air deflector
Set up
Your air tool is fully assembled when you receive it. Before using it, attach the air line and desired air system accessories. See Fig. B for the recommended
accessories and connection order. Be sure the air hose is de-pressurised when installing or removing adaptors to the air line.
Connecting the tool to an air supply (Fig. B)
• Determine if the tool needs oil and, if necessary, place two drops of oil in the air plug as shown in Fig. B. If you are using an automatic in-line oiler, check and
add oil if necessary.
• Turn the compressor on and set the regulator to the proper pressure for the size and type of fastener being used.
• Connect the tool to the air supply.
Loading the fasteners (Fig. C)
• Push the strip of fasteners into the back of the magazine with the nail head at the top of the slot and the nail points facing down.
• Allow fasteners to slide to the front of the magazine.
• Depress and hold the button on the magazine feeder.
• Pull the feeder back towards the rear of the magazine.
• Release the feeder button and allow the feeder to slide back and lock onto the rear of the strip of fasteners.
Adjusting the depth (Fig. D)
• The driving depth of the fasteners can be set with the depth adjustment wheel.
• Fasteners are not driven in deep enough: To increase the driving depth, turn depth adjustment wheel to the left.
or
• Fasteners are driven in too deeply: To reduce the driving depth, turn the depth adjustment wheel to the right.
• Test the new driving depth on a test workpiece. Repeat steps above as required.
Operating the tool
• Test the driving depth in a sample piece of wood before using. See section Adjusting the depth.
• Connect the tool to the air supply. Make sure the air pressure is in correct range denoted in section of Technical data.
FASTENING TOOLS FOR THE PROFESSIONAL
Value
KDH90V
Tacwise 2.8 – 3.7 34˚ paper collated 'D' head strip nail
50mm (2") – 90mm (3 3/8")
75 – 95
70psi / 4.82 bar
120psi / 8.27 bar
1/4" NPT
5.8 CFM @ 90psi / 6.20 bar
3.8kg (8.4lbs)
4.7m/s
2
6
Publicité
