Festool KS 120 Notice D'utilisation D'origine page 8

 Kostenlose Baupläne zum Download,
 Wissenswertes rund ums Holz - Holzlexi-
kon
REACh für Festool Produkte, deren Zubehör und
Verbrauchsmaterial: REACh ist die seit 2007 in
ganz Europa gültige Chemikalienverordnung.
Trimming attachment
Symbols
Warning of general danger
Read the Operating Instructions/Notes!
1 Scope of delivery
The trimming attachment consists of the following
main components:
(1.1) Stop profi le
(1.2) Tape measure clamp
(1.3) Support
(1.4) Support plate
(1.5) Stop fl ag
(1.6) Adjustable spacer
(1.7) Extendable end piece
(1.8) Leg support plate
(1.9) Tape measure
(1.13) Cross brace
2 Set-up
When setting up the attachment, proceed in the
sequence specifi ed.
Important: you will require a crown moulding
stop (AB-KS 120) to make the connection to the
KS 120.
Refer to Figure 1 for the arrangement and posi-
tioning of the individual parts.
Fig. 1 shows a rear view of the trimming attachment.
The following section describes how to attach the
right trimming attachment. Use the same proce-
dure to attach the left trimming attachment! Fig.
2 shows the stop mounted on both sides!
2.1 Preparations
– Secure the KS 120 to a Festool multifunction
table (MFT) or a work bench with a height of 790
mm (see operating manual KS 120).
Wir als „nachgeschalteter Anwender", also als
Hersteller von Erzeugnissen sind uns unserer
Informationspfl icht unseren Kunden gegenüber
bewusst. Um Sie immer auf den neuesten Stand
halten zu können und über mögliche Stoffe der
Kandidatenliste in unseren Erzeugnissen zu in-
formieren, haben wir folgende Website für Sie
eingerichtet. www.festool.com/reach
KA-KS 2.2 Leg support plate
The leg support plate (1.8) is designed to sup-
port the trimming attachment and is fi xed to the
extendable end piece (1.7).
– Unscrew both rotary knobs (3.1) until the two
support legs (3.3) can be inserted into the
clamping sleeves (3.4).
– Insert the support legs until the leg support
plate reaches the same height as your KS 120.
– Tighten the rotary knobs (3.1) to clamp the sup-
port legs in place.
– Screw the rotary knob (3.2) through the recess
(3.5) and into the slot nut (3.8) in the bottom slot
(3.7) on the extendable end piece to secure the
mounting plate. Note: The two cams (3.6) must
slot into the groove (3.7).
2.3 Cross brace
Secure the cross member (1.13) to the stop profi le.
– Slide the slot nut (4.2) into the stop profile
(4.1).
2.4 Stop profi le
Secure the stop profi le to the bench for the bracket
support (AB-KS 120):
– Insert the rotary knob (5.4) through the hole (5.5)
in the bracket support bench and secure the slot
nut (5.2). Do not tighten the knob yet – you must
be able to lift the slot nut approx. 5 mm above
the bracket support.
– Slide the stop profi le (5.1) onto the slot nut (5.2)
until the stop profi le is fl ush with the edge of the
bench (5.3).
– Fit the bracket support bench to the KS 120 (see
bracket support assembly instructions).
– Align the bracket support bench so that the stop
profi le is fl ush with the stop ruler on the KS 120.
Clamp the bracket support bench in place (see
bracket support assembly instructions).
–Insert a clamp (6.3) in the hole (6.1) to secure the
cross brace (6.2) to the MFT. Do not tighten yet!
–Use a long workpiece to align the trimming at-
tachment in relation to the compound mitre saw.
8