Publicité
English
When Sharpening a Blade:
•
Make sure blade remains balanced.
•
Sharpen blades at the original cutting angle.
•
Sharpen cutting edges on both ends of blade, removing
equal amounts of material from both ends.
To Sharpen Blade(s) in a Vise (Fig. EE)
1. Be sure the bail handle is released, the blades have
stopped and safety key and battery pack(s) are removed
before removing the blades.
2. Remove blades from mower. See instructions for
Removing and Installing Blades.
3. Secure blade
47
or
48
4. Wear proper eye protection and gloves and be careful
not to cut yourself.
5. Carefully file the cutting edges of the blade with a
fine tooth file
54
(not included) or sharpening stone
(not included), maintaining the angle of the original
cutting edge.
6. Check balance of blade. See instructions for Blade Balancing.
7. Replace blades on mower and tighten securely.
Blade Balancing (Fig. FF)
Check balance of each blade
mounting hole
50
over a nail or round screwdriver
clamped horizontally in a vise
rotates downward, file along the sharp edge of that dropping
end. Blade is properly balanced when neither end drops.
Cleaning (Fig. A)
WARNING: Blow dirt and dust out of all air vents with
clean, dry air at least once a week. To minimize the risk
of eye injury, always use ANSI Z87.1 (CAN/CSA Z94.3)
approved eye protection and NIOSH/OSHA/MSHA
approved respiratory protection when performing this.
WARNING: Never use solvents or other harsh
chemicals for cleaning the non‑metallic parts of the
tool. These chemicals may weaken the plastic materials
used in these parts. Use a cloth dampened only with
water and mild soap. Never let any liquid get inside the
tool; never immerse any part of the tool into a liquid.
•
Release bail handle
8
come to a stop.
•
Remove the battery pack(s) and safety key.
•
Clean out any clippings which may have accumulated on
the underside of the deck. Do not spray with water or any
other liquids.
•
After several uses, check all exposed fasteners
for tightness.
Corrosion (Fig. A)
Fertilizers and other garden chemicals contain agents which
greatly accelerate the corrosion of metals. If you mow in areas
where fertilizers or chemicals have been used, the mower
should be cleaned immediately afterward as follows:
Release bail handle
8
to turn mower off and remove battery
and safety key. Wipe all exposed parts with a damp cloth.
20
in a vise
43
.
47
or
48
by placing the keyed
43
. If either end of a blade
to turn mower off, let the blades
CAUTION: Do not pour or spray water on the mower
in an attempt to clean it. Do not store the tool on or
adjacent to fertilizers or chemicals. Such storage can
cause rapid corrosion.
Meets CPSC Safety Requirements
CRAFTSMAN mowers conform to the safety standards of
the American National Standards Institute, and the U.S.
Consumer Product Safety Commission. The blades turn when
the blade motor is running.
Accessories
WARNING: Since accessories, other than those
offered by CRAFTSMAN, have not been tested with
this product, use of such accessories with this product
could be hazardous. To reduce the risk of injury, only
CRAFTSMAN‑recommended accessories should be used
with this product.
Recommended accessories for use with your product are
available at extra cost from your local dealer or authorized
service center. If you need assistance in locating any
accessory, please contact CRAFTSMAN. Call 1‑888‑331‑4569.
Repairs
The charger and batteries are not serviceable. There are no
serviceable parts inside the charger or battery pack.
55
,
WARNING: To assure product SAFETY and RELIABILITY,
repairs, maintenance and adjustment (including
brush inspection and replacement, when applicable)
should be performed by a factory service center or
an authorized service center. Always use identical
replacement parts.
Register Online
Thank you for your purchase. Register your product now for:
• WARRAnTY sERViCE: Registering your product will
help you obtain more efficient warranty service in case
there is a problem with your product.
• COnFiRMATiOn OF OWnERshiP: In case of an
insurance loss, such as fire, flood or theft, your registration
of ownership will serve as your proof of purchase.
• FOR YOUR sAFETY: Registering your product will allow
us to contact you in the unlikely event a safety notification
is required under the Federal Consumer Safety Act.
Register online at www.craftsman.com/account/login.
Three‑Year Limited Warranty
For warranty terms, go to
www.craftsman.com/pages/warranty.
To request a written copy of the warranty terms, contact:
Customer Service at CRAFTSMAN, 701 East Joppa Road,
Towson, MD 21286 or call 1‑888‑331‑4569.
lATin AMERiCA: This warranty does not apply to products
sold in Latin America. For products sold in Latin America,
see country-specific warranty information contained in
the packaging, call the local company or see website for
warranty information.
FREE WARning lABEl REPlACEMEnT: If your warning
labels become illegible or are missing, call 1‑888‑331‑4569
for a free replacement.
Publicité
