Publicité
English
nOTE: The CMCB101 charger is not CRAFTSMAN VersaTrack™
Trackwall compatible.
SAVE THESE INSTRUCTIONS FOR
FUTURE USE
ASSEMBLY AND ADJUSTMENTS
DANGER: To reduce the risk of serious personal
injury, turn unit off and remove the safety key and
battery pack(s) before making any adjustments or
removing/installing attachments or accessories.
An accidental start‑up can cause injury.
Single Touch Handle Adjustments (Fig. E, F)
The mower is shipped in the storage position. You will need
to adjust the single touch handle
before continuing.
Raise the Single Touch Handle (Fig. E, F)
1. To unlock the single touch handle
position, squeeze the handle unlock button
nOTE: The handle unlock button
back of handle support
nOTE: The main handle
both sides of the single touch handle tubes before lifting
the single touch handle
shown in Fig. E.
2. Raise the single touch handle
Listen for an audible click and ensure the single touch
handle
1
is locked into position before proceeding.
3. Extend the main handle
clicks is heard. The single touch handle
operation position.
nOTE: Take care to not pinch, pull or otherwise stress
the cord
23
.
Adjusting the Main Handle Height (Fig. G)
The main handle
extends to accommodate taller users.
4
1. To extend the main handle
position, press the handle release button
main handle away from the handle support
audible click is heard, indicating that it is locked into the
lower height position.
nOTE: The handle release button
bottom of handle support
2. To extend the main handle
position, press the handle release button
main handle away from the handle support
audible click is heard, indicating that it is locked into the
upper height position.
3. Ensure the main handle
before proceeding.
4. To retract the main handle
position, press the handle release button
main handle
towards the handle support
4
audible click is heard, indicating that it is locked into
the lower height position.
5. Ensure the main handle
before proceeding.
16
1
to the operating position
1
from the storage
3
.
3
is located on the
2
.
4
must pop out slightly from
1
from the storage position as
1
to the locked position.
4
outward until a set of audible
1
is now in the
4
to the lower height
5
and pull the
2
until an
5
is located on the
2
.
to the upper height
4
and pull the
5
until an
2
4
locks into position
4
to the lower height
and push the
5
until an
2
4
locks into position
Storage Mode (Fig. H—M)
DANGER: MAKE CERTAIN THE SAFETY KEY IS
REMOVED TO PREVENT ACTUATION BEFORE
REMOVING OR INSTALLING BATTERY.
DANGER: Turn unit off and remove safety key and
battery pack(s).
1. To retract the main handle
button
5
and push the main handle
handle support
2
until two audible clicks are heard,
indicating that both sides of the handles are locked
into position. The main handle
against the handle support.
nOTE: The main handle
windows
24
. If they are not engaged as shown in Fig. H,
press the main handle
until two audible clicks are heard and both sides of
handle windows
24
nOTE: Ensure the two storage latches
the single touch handle
in Fig. K before lowering the single touch handle
the storage position.
2. Fold the single touch handle
wheels
27
into storage position. Listen for two audible
clicks as the two storage latches
storage slots
26
as shown in Fig. K.
3. Ensure the single touch handle
position before proceeding.
4. The mower can be stored standing up, with the collection
bag removed, or flat on its wheels as shown in Fig. M.
nOTE: Take care to not pinch, pull or otherwise stress
the cord
23
.
Grass Collection Bag (Fig. N)
DANGER: Turn unit off and remove safety key and
battery pack(s).
1. Lift the rear door cover
and place the grass collection bag
so the bag lugs
28
slide into the slots
plastic surfaces of the handle brackets. Then lower the
rear door cover
15
.
nOTE: If installed, remove rear side discharge chute
and ensure the rear door cover
installing grass collection bag
Mulching (Fig. O)
DANGER: Turn unit off and remove safety key and
battery pack(s).
1. To operate mower in mulching mode, remove the grass
collection bag
16
or rear side discharge chute
2. Lift the rear door cover
plug
18
fully into the mower.
3. Ensure the pins
30
on the mulching plug
the slots
31
on the mower as shown in Fig. O.
4. Be sure rear door cover
Side Discharge (Fig. P)
DANGER: Turn unit off and remove safety key and
battery pack.
4
, press the handle release
4
towards the
4
must be fully seated
4
must fully engage the handle
4
towards the handle support
are closed as shown in Fig. I.
25
at the back of
1
tubes pop outward as shown
1
towards the front
25
slide into the
1
is locked into storage
15
, remove mulching plug
16
onto the mower
29
on the inside
is fully up before
15
.
16
15
and slide the mulching
18
15
is closed.
2
into
1
18
,
19
19
.
engage
Publicité
