Publicité
TECHNICAL DATA
Type
Voltage
Frequency
Power input (DC-Mode)
Power input (AC-Mode)
Lightning time (5.0 Ah)
Main panel & side panel
Mode High
Mode Medium
Mode Low
Main panel
Mode High
Mode Medium
Mode Low
Side panel
Mode High
Mode Medium
Mode Low
Luminous flux
Main panel & side panel
Mode High
Mode Medium
Mode Low
Main panel
Mode High
Mode Medium
Mode Low
Side panel
Mode High
Mode Medium
Mode Low
Colour rendering index (CRI)
Colour temperature
Weight without battery
Weight according EPTA-Procedure 01/2014 (2.0...12.0 Ah)
Recommended ambient operating temperature
Recommended battery types
Recommended charger
WARNING!
Read all safety warnings and all instructions.
Failure to follow the warnings and instructions may result in electric shock,
fire and/or serious injury.
Save all warnings and instructions for future reference.
SAFETY INSTRUCTIONS BATTERY-LAMP
Warning: Do not direct the light beam at persons or animals and do not
stare into the light beam yourself (not even from a distance). Staring into
the light beam may result in serious injury or vision loss.
The light source of this luminaire is not replaceable; when the light source
reaches its end of life the whole luminaire shall be replaced.
This product contains a light source of energy efficiency class D.
Ensure that the luminaire does not cause harm if its magnet fails to keep
it in position.
Don't use this tool in wet areas.
ADDITIONAL SAFETY WARNINGS
Ensure the hanging surface is sturdy and the rafter hook is secure before
using. A falling light could strike people or objects below.
To reduce the risk of injury or damage to the tool, ensure the nail can
support the weight of the tool.
Make sure that all magnets make contact with the magnetic surface.
Make sure that the magnetic surface is free from materials that could
prevent the magnets from attaching.
18
M18 MDTL
Battery-Lamp
18 V (DC) / 100 - 240 V (AC)
50-60 Hz
29 W
35 W
3 h
6 h
11 h
8 h
18 h
30 h
4 h
9 h
16 h
4500 lm
2000 lm
1200 lm
1500 lm
650 lm
400 lm
3000 lm
1300 lm
800 lm
80
4000 K
3,05 kg
3,3 ... 4,4 kg
-18 °C ... +50 °C
M18 B...; M18 HB
M12-18...; M18 DFC; M1418 C6
Remove the battery pack before starting any work on the appliance.
Do not dispose of used battery packs in the household refuse or by
burning them. Milwaukee Distributors offer to retrieve old batteries to
protect our environment.
Do not store the battery pack together with metal objects (short circuit
risk).
Use only compatible Milwaukee chargers from the same battery platform
for charging battery packs. Do not use battery packs from other systems.
Battery acid may leak from damaged batteries under extreme load or
extreme temperatures. In case of contact with battery acid wash it off
immediately with soap and water. In case of eye contact rinse thoroughly
for at least 10 minutes and immediately seek medical attention.
Warning! To reduce the risk of fire, personal injury, and product damage
due to a short circuit, never immerse your tool, battery pack or charger
in fluid or allow a fluid to flow inside them. Corrosive or conductive fluids,
such as seawater, certain industrial chemicals, and bleach or bleach
containing products, etc., can cause a short circuit.
SPECIFIED CONDITIONS OF USE
The battery lamp can be used as lighting independently of a mains power
supply.
Do not use this product in any other way as stated for normal use.
ENGLISH
NOTES FOR LI-ION BATTERIES
Use of Li-Ion batteries
Batteries which have not been used for some time should be recharged
before use.
Temperatures in excess of 50°C reduce the performance of the battery.
Avoid extended exposure to heat or sunshine (risk of overheating).
The contacts of chargers and batteries must be kept clean.
For an optimum life-time, the batteries have to be fully charged, after
used.
To obtain the longest possible battery life remove the battery pack from
the charger once it is fully charged.
For battery storage longer than 30 days:
Store the battery where the temperature is below 27°C and away from
moisture
Store the battery in a 30% - 50% charged condition
Every six months of storage, charge the battery as normal.
Transport of Li-Ion batteries
Lithium-ion batteries are subject to the Dangerous Goods Legislation
requirements.
Transportation of those batteries has to be done in accordance with local,
national and international provisions and regulations.
• The user can transport the batteries by road without further
requirements.
• Commercial transport of Lithium-Ion batteries by third parties is subject
to Dangerous Goods regulations. Transport preparation and transport
are exclusively to be carried out by appropriately trained persons and
the process has to be accompanied by corresponding experts.
When transporting batteries:
• Ensure that battery contact terminals are protected and insulated to
prevent short circuit.
• Ensure that battery pack is secured against movement within
packaging.
• Do not transport batteries that are cracked or leak.
Check with forwarding company for further advice.
MAINS CONNECTION
Connect only to single-phase AC current and only to the system voltage
indicated on the rating plate. It is also possible to connect to sockets
without an earthing contact as the design conforms to safety class II.
ADVICES FOR OPERATION
If both battery and extension cord are inserted, AC power will be used,
with DC power as a backup.
NOTE: This tool does not charge battery packs.
MAINTENANCE
Use only Milwaukee accessories and Milwaukee spare parts. Should
components need to be replaced which have not been described, please
contact one of our Milwaukee service agents (see our list of guarantee/
service addresses).
If needed, an exploded view of the tool can be ordered. Please state the
machine type printed as well as the six-digit No. on the label and order the
drawing at your local service agents or directly at: Techtronic Industries
GmbH, Max-Eyth-Straße 10, 71364 Winnenden, Germany.
SYMBOLS
Please read the instructions carefully before starting the
machine.
CAUTION! WARNING! DANGER!
Do not stare at the operating light source
Caution – hot surfaces!
This tool is only suitable for indoor use. Never expose tool
to rain.
The light source and the control device cannot
be exchanged.
LED
LED
This product contains a light source of energy
efficiency class D.
L E
D
Do not dispose of waste batteries, waste electrical and
electronic equipment as unsorted municipal waste. Waste
batteries and waste electrical and electronic equipment must
be collected separately.
Waste batteries, waste accumulators and light sources have
to be removed from equipment.
Check with your local authority or retailer for recycling
advice and collection point.
According to local regulations retailers may have an
obligation to take back waste batteries and Waste electrical
and electronic equipment free of charge.
Your contribution to re-use and recycling of waste batteries
and waste electrical and electronic equipment helps to
reduce the demand of raw materials.
Waste batteries, in particular containing lithium and waste
Electrical and electronic equipment contain valuable,
recyclable materials, which can adversely impact the
environment and the human health, if not disposed of in an
environmentally compatible manner.
Delete personal data from waste equipment, if any.
Class II tool.
Tool in which protection against electric shock does not rely
on basic insulation only, but in which additional safety pre-
cautions, such as double insulation or reinforced insulation,
are provided.
There being no provision for protective earthing or reliance
upon installation conditions.
European Conformity Mark
UK Conformity Mark
Ukraine Conformity Mark
EurAsian Conformity Mark
ENGLISH
19
Publicité
