Publicité
Before starting
Position the device where you want it. Insert the plug into the electrical outlet and switch it on
if necessary.
Mains power supply of the device: 230V 50Hz
Insert the mains plug into the wall socket (230 V).
Warning:
•
Before using the unit, check that the power supply is compatible with the 230V (50 Hz)
rating of the unit.
•
Do not plug or unplug the power cord with wet hands.
•
When you are planning not to use the appliance for a prolonged period (holiday, etc.),
disconnect the plug from the mains outlet.
•
When you disconnect the plug from the power outlet, hold the end of the plug; do not pull
on the cord to avoid electric shocks caused by the damaged cable.
Automatic standby
•
When you are playing audio from a connected accessory, the micro sound system
automatically goes into standby mode if:
•
you don't press any buttons for 10 minutes;
•
the connected accessory has not sent any audio data for 10 minutes.
Operation
•
Press the POWER button to turn the device ON or OFF.
Adjust the volume with the remote control
•
Press Volume + to increase the volume, press Volume - to lower the volume.
•
Check the screen display, which should confirm the volume adjustment.
Mute function
•
Press the MUTE button on the remote control. The volume is muted and the word "Mute"
appears on the LCD screen. Press this button again to cancel the mute function.
Set the clock (in standby mode)
1.
Press ≡ once to "SET CLOCK", press
2.
Press < or > to choose the 24hr or 12hr format, then press
3.
Press < or > to set the current time, press
4.
Press < or > to set the current minutes, press
▷
5.
Press
to save the time setting.
Set the alarm (in Standby mode)
1.
Once you have set the clock, you can set the alarm.
2.
"Alarm Setup" is displayed. Press the "
3.
Press < or > to set the current time, press
▷
to confirm and the "24H" symbol will flash.
▷
to confirm.
▷
to confirm and the minutes will flash.
▷
to confirm, and "SAVE YES" will flash.
▷
" button to make your choice.
▷
to confirm and the minutes will flash.
- EN 28 -
4.
Press < or > to set the current minutes and press
5.
Press < / > to adjust the alarm volume.
6.
Press < / > to select the alarm source (buzzer, DAB, FM, CD, USB) and press
7.
Press < / > to adjust the alarm duration. You can choose between 15, 30, 45 and 60
▷
minutes. Press
to confirm.
8.
Press < / > to save the alarm settings.
Use
DAB radio mode
Carefully deploy the telescopic aerial.
Press the POWER button to turn on the device, which will automatically switch to DAB mode.
Automatic search
1.
Press the ≡ button to select "DAB MODE" (if the device is not already in DAB mode). If
this is the first time the device has been set to DAB mode, it will automatically begin an
automatic search for available stations. (Once DAB mode has been used, the device will
automatically select the station you were listening to before)
▷
2.
Press the
/à button to start the automatic search to find available stations. During the
search, a progress bar will be displayed to indicate how the process is progressing.
Manual search
1.
Press the ≡ button on the device to select "DAB MODE".
2.
Press the < or > button to select "Manual tune" and press the
service menu.
3.
Press < or > to select the station you want. The signal strength will be displayed.
4.
Press MENU to exit the search.
5.
If no stations are found, make sure that the aerial is fully extended and test the reception
by carrying out another automatic search in a different location.
▷
to confirm.
▷
/à button to enter the
- EN 29 -
▷
Publicité
