Publicité
ENGLISH
Operation
de
Preparation
Keep the packaging material for safe storage or
en
transport later.
f Check that the contents are complete.
fr
f Check all the parts for possible transport damage.
it
Safety
Handle with care! Damage due to incorrect power
supply.
es
f Only operate the appliance with an alternating cur-
rent and with the voltage stated on the nameplate.
pt
Charging the battery
Before the appliance is used for the first time, it
nl
should be charged for approx. 2 hours!
sv
1. Connect the appliance plug (J) on the plug-in transformer to
the charging stand socket (E) (Fig. 2ⓐ).
no
Battery overcharging is prevented thanks to intelligent
charge management.
fi
2. Connect the plug-in transformer to the mains socket
(Fig. 2ⓑ).
tr
3. Switch off the appliance using the on/off switch (Fig. 3ⓑ).
4. Place the appliance on the charging station (Fig. 2)
pl
·
During charging, the charging indicator (C) flashes
at evenly spaced intervals. When the battery is
fully charged, the charging indicator flashes at a
cs
different rate (10 on / 1 off).
·
After the appliance has been removed from the
sk
charging stand, the display goes out (power sav-
ing mode).
It takes no more than 120 minutes for the appli-
·
hu
ance to charge to full capacity.
sl
Battery operation
1. Switch on the appliance using the on/off switch and switch
off after use (Fig. 3ⓐ/ⓑ).
ro
·
With the battery fully charged, the appliance can
bg
be operated for up to 100 minutes. This capacity
is attained after approx. 5 - 10 charging cycles.
·
In case of insufficient maintenance of the
ru
blade set, the operating time can be reduced
considerably.
uk
el
ar
12
Operation
Cutting with the attachment comb
The appliance can also be operated with an attachment comb.
f The attachment comb has 5 detent positions for adjusting
the length of cut.
f The further the attachment comb is pushed in (retracted),
the shorter the length of cut.
The length of cut can be adjusted from 3 mm
(Fig. 5ⓐ) to 6 mm (Fig. 5ⓑ).
Attaching/removing the attachment comb
1. Slide the attachment comb on to the blade set in the direc-
tion of the arrow until it reaches the limit stop (Fig. 4ⓐ).
2. The attachment comb can be removed by pushing it in the
direction of the arrow (Fig. 4ⓑ).
Maintenance
Cleaning and care
Danger! Electric shock due to penetration of
liquid.
f Switch off the appliance before any cleaning of
maintenance takes place.
f Do not immerse the appliance in water!
f Do not allow any liquid to get inside the appliance.
f Only place the appliance back on the charging
station if it is completely dry.
Handle with care! Danger from aggressive
chemicals.
Aggressive chemicals could damage the appliance
and accessories.
f Never use solvents or scouring agents.
f Only use cleaning agents and blade set oil recom-
mended by the manufacturer.
Hygienic spray and blade set oil are available from
your dealer or our service centre.
f Remove the attachment comb (Fig. 4ⓑ) after every use
and lift the blade set out of the housing (Fig. 6ⓐ). Use the
cleaning brush to remove any cut hairs from the housing
opening and from the blade set (Fig. 7). The cleaning lever
can also be pressed. This allows the cut hairs that accumu-
late between the bottom blade and the top blade to be eas-
ily removed using the cleaning brush (EASY CLEANING).
f The charging contacts on the appliance and on the charging
stand should always be kept clean.
f Only wipe the appliance with a soft, slightly damp cloth.
f The blade set using the hygienic spray.
f Oil the blade set with the blade set oil (Fig. 8).
f For a good and long-lasting cutting performance, it
is important to oil the blade set frequently
Publicité
