Publicité
OBJ_BUCH-1600-005.book Page 34 Friday, December 16, 2016 9:23 AM
34 | English
Permissible Workpiece Dimensions
Maximum workpiece sizes:
Mitre/Bevel Angle
Horizontal
Vertical
0°
45°
0°
45°
45°
45°
Minimum workpiece sizes (= all workpieces that can be
clamped left or right from the saw blade with the supplied
material clamp 40): 128 x 40 mm (length x width)
Cutting depth, max.
Workpiece against fence
Workpiece against distance-stop
(moved toward the front)
Cutting Off
– Firmly clamp the workpiece as appropriate for its dimen-
sions.
– Adjust the requested mitre and/or bevel angle.
– Switch on the machine.
– Press lever 22 and slowly guide the tool arm downward by
handle 4.
– Saw through the workpiece applying uniform feed.
– Switch off the machine and wait until the saw blade has
come to a complete stop.
– Guide the tool arm slowly upward.
Sawing Workpieces of the Same Length (see figure P)
The material stop 27 can be used for easily sawing work-
pieces to the same length.
The material stop can be mounted on either side of the saw
table extension 15.
Sawing Profile Strips/Mouldings (Floor and Ceiling Strips)
Profile strips/mouldings can be sawn in two different ways:
– Placed against the fence
– Lying flat on the saw table.
Floor Strips/Mouldings
The following table contains instructions for sawing floor strips/mouldings.
Settings
Bevel angle
Floor strip/moulding
Inner corner
Horizontal mitre angle
Positioning of work-
piece
The finished work-
piece is located ...
1 609 92A 348 | (16.12.16)
Workpiece against fence
0°
75 x 200
0°
75 x 141
38 x 200
38 x 141
– Loosen lock screw 28 and swing the material stop 27 over
– Retighten lock screw 28.
– Adjust the saw table extension 15 to the desired length
(0°/0°):
75 mm
Special Workpieces
(0°/0°):
100 mm
When sawing curved or round workpieces, these must be
especially secured against slipping. At the cutting line, no gap
may exist between workpiece, fence and saw table.
Provide for special fixtures, if required.
Replacing Insert Plates (see figure Q)
The red insert plates 39 can become worn after prolonged
use of the machine.
Replace defective insert plates.
– Bring the power tool into the working position.
– Unscrew screws 56 with the provided hex key (4 mm) 17
– Insert the new right-hand insert plate.
– Screw the insert plate with the screws 56 as far as possible
– Repeat the work steps in the same manner for the left-hand
Always make trial cuts with the mitre angle setting first on
scrap wood.
Placed
against the
fence
0°
Left side
45° left
Bottom edge on
Bottom edge on
saw table
... to the left of the
... to the right of the
cut
Height x Width [mm]
Workpiece against distance-stop
(moved toward the front)
100 x 150
100 x 100
clamping screw 55.
(see "Extending the Saw Table", page 32).
and remove the old insert plates.
to the right, so that the saw blade does not come in contact
with the insert plate throughout the complete possible rip-
ping length.
insert plate.
Lying flat on
the saw table
Right side
Left side
45° right
0°
Upper edge against
saw table
the fence
... to the left of the
cut
cut
–
–
45°
Right side
0°
Bottom edge
against the fence
... to the left of the
cut
Bosch Power Tools
Publicité
