Télécharger Imprimer la page

Publicité

Liens rapides

Website:
www.horizonglobal.com
Technical Assistance: 800-632-3290
TechnicalSupport@horizonglobal.com
To prevent SERIOUS INJURY, DEATH, or PROPERTY DAMAGE:
ALWAYS read, understand, follow warnings, and instructions for
your hitch BEFORE installation. Keep for future reference.
DO NOT cut, weld, or modify this trailer hitch.
Regularly check that all fasteners are tight, and your hitch is
securely mounted to vehicle. In order to ensure hitch towing
capacity and longevity of the product, ensure that all fasteners are
torqued to the prescribed torque within this Installation
Instruction.
Towing trailers beyond the maximum recommended gross trailer
weight (GTW) of your vehicle could result in engine, transmission,
or structural damage. This could also lead to loss of vehicle control,
vehicle rollover, and/or personal injury.
Read your owner's manual. If your vehicle is NOT recommended
for towing and/or installation of a tow hitch for an accessory
carrier, the vehicle owner accepts responsibility and assumes all
risk stated above.
NEVER exceed your vehicle manufacturer's recommended towing
capacity or the hitch towing capacities listed below.
Hitch Type
Max Gross Trailer
Weight Carrying
5000 lb. (2267 kg)
Weight Distributing
5000 lb. (2267 kg)
©2024 Horizon Global Corporation. - Printed in Mexico
Installation Instructions
PART NUMBERS: 76649, 84649, CQT76649
Max Tongue
Weight
Weight
500 lb. (227 kg)
500 lb. (227 kg)
LIMITED LIFETIME WARRANTY
1.
Limited Lifetime Warranty ("Warranty"). Horizon Global Corporation. ("We", "Us" or
"Our") warrants to the original consumer purchaser only ("You" or "Your") that the product
will be free from material defects in both material and workmanship, ordinary wear and tear
excepted. The Warranty is valid only if (a) the products are returned to Us for inspection and
testing; (b) Our inspection discloses to Our satisfaction that any alleged nonconformance are
material and have not been caused by misuse, neglect, wear and tear, improper installation,
unsuitable storage, improper repair, alteration, or accident; and (c) the products were
installed, maintained and used in accordance with Our instructions. THE WARRANTY IS
MADE IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED (OTHER
THAN THE WARRANTY OF TITLE AS PROVIDED BY THE UNIFORM
COMMERCIAL CODE IN EFFECT IN MICHIGAN), INCLUDING WITHOUT
LIMITATION, ANY WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE, SAID WARRANTIES BEING EXPRESSLY DISCLAIMED.
2.
Obligations of Purchaser. To make a Warranty claim, contact Us at our principal address of
127 Public Square Suite 5300, Cleveland, OH, 44114, 800-632-3290, identify the product
by model number, and follow the claim instructions that will be provided. Any returned
product that is replaced by Us becomes our property. You may be responsible for return
shipping costs. Please retain your purchase receipt to verify date of purchase and that You
are the original consumer purchaser. The product and the purchase receipt must be provided
to Us in order to process Your Warranty claim.
3.
Exclusive Remedy. Product replacement is Your sole and exclusive remedy under this
Warranty. We shall not be liable for service or labor charges incurred in removing or
replacing a product. IN NO EVENT WILL WE BE RESPONSIBLE FOR ANY INDIRECT,
SPECIAL, CONSEQUENTIAL OR PUNITIVE DAMAGES.
4.
Assumption of Risk. You acknowledge and agree that any use of the product for any
purpose other than the specified use(s) stated in the product instructions is at Your own risk.
5.
Governing Law. This limited warranty gives You specific legal rights, and You also may
have other rights which may vary from state to state. This limited warranty is governed by the
laws of the State of Michigan, without regard to rules pertaining to conflicts of law. The state
courts located in Cuyahoga County, Ohio shall have exclusive jurisdiction for any disputes
relating to this warranty.
Rev. 03/2024
Sheet 1 of 21
Scan for safe towing
tip, or visit
http://qr.towingpro
ducts.net/qrproduct
s/qr-product
76649NP
6-5-24
Rev. A

Publicité

loading

Sommaire des Matières pour Horizon Global 76649

  • Page 1 TechnicalSupport@horizonglobal.com LIMITED LIFETIME WARRANTY Limited Lifetime Warranty (“Warranty”). Horizon Global Corporation. ("We", “Us” or “Our”) warrants to the original consumer purchaser only ("You" or “Your”) that the product To prevent SERIOUS INJURY, DEATH, or PROPERTY DAMAGE: will be free from material defects in both material and workmanship, ordinary wear and tear excepted.
  • Page 2 Make Model Mazda CX-90 • Installation times are listed on Horizon Global websites or found in the downloadable application guides. • Installation difficulty levels are based on time and • Visit our website for the most up-to- effort involved. They may vary depending on installer date information regarding level of expertise and condition of the vehicle.
  • Page 3 Observe safety precautions when working beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch. This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. ©2024 Horizon Global Corporation. - Printed in Mexico Sheet 3 of 21...
  • Page 4 Observe safety precautions when working beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch. This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. ©2024 Horizon Global Corporation. - Printed in Mexico Sheet 4 of 21...
  • Page 5 1” wide spacer block (item 4). by rotating clip 1/4 turn. See Figures 1, 2, 3. Enlarge Access Hole, both sides Figure 3. Figure 4. ©2024 Horizon Global Corporation- Printed in México Sheet 5 of 21 76649NP 6-5-24 Rev. A...
  • Page 6 Tighten all 7/16-14 Gr5 fasteners with torque wrench to 50 Lb.-Ft. (68 N*M) Proper torque is needed to keep the hitch secure to the vehicle when towing. For additional security, thread locker can be used on all fasteners. ©2024 Horizon Global Corporation - Printed in México Sheet 6 of 21 76649NP 6-5-24 Rev.
  • Page 7 8. Tighten 7/16-14 locknuts until snug against support panel. Tighten M6 hex bolts with torque wrench to 53 IN. – LB. ( 6 N*M ) Fascia Support Panel ⑥ Figure 7. ©2024 Horizon Global Corporation - Printed in México Sheet 7 of 21 76649NP 6-5-24...
  • Page 8 TechnicalSupport@horizonglobal.com GARANTIE À VIE LIMITÉE Garantie à vie limitée (« Garantie »). Horizon Global (« Nous », « Notre ») garantit à l’acheteur initial seulement (« Vous », « Votre ») que le produit sera exempt de vices de Pour éviter des BLESSURES GRAVES, LA MORT matières et de fabrication, exception faite de l’usure normale.
  • Page 9 Modèles Mazda CX-90 • Les temps d'installation sont répertoriés sur les sites Web de Horizon Global ou dans les guides d'application téléchargeables. • Les niveaux de difficulté d'installation sont basés sur le • Visitez notre site Web pour obtenir de temps et les efforts nécessaires.
  • Page 10 Instructions d’installation Visserie: 76649F Toujours porter des LUNETTES DE PROTECTION lors de l'installation NUMÉROS DE PIÈCE : 76649, 84649, CQT76649 ① de l'attelage. Qty. (2) Boulon, M14-1.50 x 45 CL10.9 ② Qty. (2) Rondelle conique M14 Couverture de l'attelage Boulon de carrosserie Qty.
  • Page 11 Instructions d’installation ③ NUMÉROS DE PIÈCE : 76649, 84649, CQT76649 Weldnut ④ Rail du cadre Fascia Support Panel Trou d'accès ⑤ 1/2” Rondelle ① plate ② ⑥ ③ ⑥ ④ Rondelle conique Dents orientées contre l'attelage Figure 7. ⑤ Visserie similaire ④...
  • Page 12 Voir les figures 1, 2 et 3. Retour au propriétaire. Agrandissement du trou d'accès, des deux côtés Figure 3. Figure 4. ©2024 Horizon Global Corporation. - Imprimé au Mexique Feuille 11 de 21 76649NP 6-5-24 Rev. A...
  • Page 13 2ème Serrer toutes les fixations 7/16-14 Gr5 à l'aide d'une clé dynamométrique à 68 N*M. Pour plus de sécurité, du frein filet peut être utilisé sur toutes les fixations. ©2024 Horizon Global Corporation. - Imprimé au Mexique Feuille 11 de 21 76649NP 6-5-24 Rev.
  • Page 14 8. Serrer les contre-écrous 7/16-14 jusqu'à ce qu'ils soient bien ajustés contre le panneau de support. Serrer les boulons hexagonaux M6 à l'aide d'une clé dynamométrique à 53 IN. - LB. ( 6 N*M ) Fascia Support Panel ⑥ Figure 7. ©2024 Horizon Global Corporation. - Imprimé au Mexique Feuille 11 de 21 76649NP 6-5-24 Rev. A...
  • Page 15 TechnicalSupport@horizonglobal.com GARANTÍA LIMITADA DE POR VIDA Garantía limitada de por vida ("Garantía") Horizon Global ("nosotros", "nos" o "nuestro/a/s") garantiza al comprador original únicamente ("usted" o "su/s") que el producto estará libre de defectos significativos tanto en materiales como en mano de obra, con la Para evitar DAÑOS DE GRAVEDAD, A LA PROPIEDAD o LA...
  • Page 16 Modelos Mazda CX-90 • Los tiempos de instalación se indican en los sitios web de Horizon Global o se encuentran en las guías de aplicación descargables. • Los niveles de dificultad de instalación se basan en el tiempo • Visite nuestro sitio web para la y el esfuerzo requeridos.
  • Page 17 Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York, V.E.S.C. Regulación V-5 y SAE J684. ©2024 Horizon Global Corporation. - Impreso en México Hoja 17 de 21...
  • Page 18 Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York, V.E.S.C. Regulación V-5 y SAE J684. ©2024 Horizon Global Corporation. - Impreso en México Hoja 18 de 21...
  • Page 19 Véanse las figuras 1, 2 y 3. Devuelva al propietario. (elemento 4). Ampliar el orificio de acceso por ambos lados Figura 3. Figura 4. ©2024 Horizon Global Corporation. - Impreso en México Hoja 19 de 21 76649NP 6-5-24 Rev. A...
  • Page 20 Para mayor seguridad, se 2º Apriete todos los tornillos 7/16-14 Gr5 con la llave dinamométrica a 50 Lb.-Ft. (68 N*M) puede utilizar fijador de roscas en todas las fijaciones. ©2024 Horizon Global Corporation. - Impreso en México Hoja 20 de 21 76649NP 6-5-24 Rev.
  • Page 21 8. Apriete las contratuercas 7/16-14 hasta que queden ajustadas contra el panel de soporte. Apriete los tornillos hexagonales M6 con una llave dinamométrica a 53 IN. - LB. ( 6 N*M ) Fascia Support Panel ⑥ Figura 7. ©2024 Horizon Global Corporation. - Impreso en México Hoja 21 de 21 76649NP 6-5-24 Rev. A...

Ce manuel est également adapté pour:

84649Cqt76649