Publicité

Les langues disponibles

Les langues disponibles

Website:
www.horizonglobal.com
Technical Assistance: 800-632-3290
TechnicalSupport@horizonglobal.com
To prevent SERIOUS INJURY, DEATH or PROPERTY DAMAGE:
ALWAYS read, understand and follow warnings and instructions
for your hitch BEFORE installation. Keep for future reference.
DO NOT cut, weld or modify this receiver.
CHECK all fasteners are tight and your hitch is securely mounted
to your vehicle periodically.
ALWAYS read, understand and follow all warnings and
instructions for your vehicle and for other accessories you will use
with your hitch BEFORE use.
LOAD the trailer heavier in front.
DO NOT exceed lower of towing vehicle manufacturer's rating or:
Hitch Type
Max Gross Trailer
Weight Carrying
3500 lb. (1587 kg)
Weight Distributing
ALWAYS wear your seatbelt.
SLOW DOWN when towing, NEVER exceed any posted speed limit.
If EXCESS SWAY occurs, take your foot off the gas pedal and hold
the steering wheel as steady as possible. DO NOT apply your
brakes and DO NOT speed up.
©2022 Horizon Global™ Corp - Printed in Mexico
Installation Instructions
PART NUMBERS: 76626, 84626, CQT76626
Max Tongue
Weight
Weight
525 lb. (238 kg)
N/A
N/A
LIMITED LIFETIME WARRANTY
Limited Lifetime Warranty ("Warranty"). Horizon Global ("We", "Us" or "Our")
1.
warrants to the original consumer purchaser only ("You" or "Your") that the product will be
free from material defects in both material and workmanship, ordinary wear and tear
excepted. The Warranty is valid only if (a) the products are returned to Us for inspection and
testing; (b) Our inspection discloses to Our satisfaction that any alleged nonconformance are
material and have not been caused by misuse, neglect, wear and tear, improper installation,
unsuitable storage, improper repair, alteration, or accident; and (c) the products were
installed, maintained and used in accordance with Our instructions. THE WARRANTY IS
MADE IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED (OTHER
THAN THE WARRANTY OF TITLE AS PROVIDED BY THE UNIFORM
COMMERCIAL CODE IN EFFECT IN MICHIGAN), INCLUDING WITHOUT
LIMITATION, ANY WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE, SAID WARRANTIES BEING EXPRESSLY DISCLAIMED.
2.
Obligations of Purchaser. To make a Warranty claim, contact Us at our principal address of
47912 Halyard Drive, Suite 100, Plymouth, MI 48170, 1-800-632-3290, identify the product
by model number, and follow the claim instructions that will be provided. Any returned
product that is replaced by Us becomes our property. You may be responsible for return
shipping costs. Please retain your purchase receipt to verify date of purchase and that You
are the original consumer purchaser. The product and the purchase receipt must be provided
to Us in order to process Your Warranty claim.
3.
Exclusive Remedy. Product replacement is Your sole and exclusive remedy under this
Warranty. We shall not be liable for service or labor charges incurred in removing or
replacing a product. IN NO EVENT WILL WE BE RESPONSIBLE FOR ANY INDIRECT,
SPECIAL, CONSEQUENTIAL OR PUNITIVE DAMAGES.
4.
Assumption of Risk. You acknowledge and agree that any use of the product for any
purpose other than the specified use(s) stated in the product instructions is at Your own risk.
5.
Governing Law. This Warranty gives You specific legal rights, and You also may have
other rights which vary from state to state. This Warranty is governed by the laws of the
State of Michigan, without regard to rules pertaining to conflicts of law. The state courts
located in Oakland County, Michigan shall have exclusive jurisdiction for any disputes
relating to this Warranty.
Rev 8/2015
Sheet 1 of 21
Scan for safe towing
tip, or visit
http://qr.towingpro
ducts.net/qrproduct
s/qr-product
76626NP
10-3-22
Rev. A

Publicité

Table des Matières
loading

Sommaire des Matières pour Horizon Global 76626

  • Page 1 TechnicalSupport@horizonglobal.com LIMITED LIFETIME WARRANTY Limited Lifetime Warranty (“Warranty”). Horizon Global ("We", “Us” or “Our”) warrants to the original consumer purchaser only ("You" or “Your”) that the product will be To prevent SERIOUS INJURY, DEATH or PROPERTY DAMAGE: free from material defects in both material and workmanship, ordinary wear and tear •...
  • Page 2: Installation Instructions

    Installation Difficulty: Expert Make Model(s) Mercedes • Installation times are listed on Horizon Global websites or found in the downloadable application guides. * Visit our website for the most • Installation difficulty levels are based on time and effort up-to-date information regarding application years, involved.
  • Page 3 Observe safety precautions when working beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch. This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. ©2022 Horizon Global™ Corp - Printed in Mexico Sheet 3 of 21...
  • Page 4 1. Remove splash guard – Using 10mm socket, remove (8) screws from bottom of fascia where splash guard is located. Using flat head screwdriver, remove (2) push rivets from same area. Remove splash guard and return to owner. ©2022 Horizon Global™ Corp - Printed in Mexico Sheet 4 of 21...
  • Page 5 3. Remove/Trim heat shield/Reinstall – a.) Using 8mm socket, remove (2) screws from underside of vehicle (found near exhaust (1) per side). Then remove (4) nuts from the center of the heat shield using the same socket. Gently remove and set aside for later use. ©2022 Horizon Global™ Corp - Printed in Mexico Sheet 5 of 21...
  • Page 6 Make sure the hitch sits straight with location marked. Lower the hitch down and use drill to drill a ½” hole, both sides. Drilled Hole ©2022 Horizon Global™ Corp - Printed in Mexico Sheet 6 of 21 76626NP 10-3-22 Rev.
  • Page 7 ② Figure 1 8. Reinstall exhaust and sensor – Raise exhaust back into position and secure sensor in place using original hardware removed in step 2. ©2022 Horizon Global™ Corp - Printed in Mexico Sheet 7 of 21 76626NP 10-3-22...
  • Page 8: Garantie À Vie Limitée

    TechnicalSupport@horizonglobal.com GARANTIE À VIE LIMITÉE Garantie à vie limitée (« Garantie »). Horizon Global (« Nous », « Notre ») garantit à l’acheteur initial seulement (« Vous », « Votre ») que le produit sera exempt de vices de Pour prévenir les blessures SÉVÈRES, FATALES ou les DOMMAGES matières et de fabrication, exception faite de l’usure normale.
  • Page 9 Instructions d’installation Numériser pour des instructions avec NUMÉROS DE PIÈCES : 76626, 84626, CQT76626 PHOTOS ou visiter Site Internet: www.horizonglobal.com http://qr.towingprod ucts.net/qrproducts/q Assistance technique: 800-632-3290 r-product TechnicalSupport@horizonglobal.com Applications: Difficulté d’installation : Expert Marque Modèles • Les heures d’installation sont répertoriées sur les sites Web Mercedes d’Horizon Global ou dans les guides d’application...
  • Page 10 Instructions d’installation Ens. fixations : 76626F NUMÉROS DE PIÈCE : 76626, 84626, CQT76626 ① Qté. (4) Fil de traction ½ po Longeron ② Qté. (4) Rondelle à dents Rondelle ½ po Qté. (4) Écrou hex. Trous percés B. Aligner le C.
  • Page 11 1. Retirez le pare-éclaboussures - À l'aide d'une douille de 10 mm, retirez les (8) vis du bas du carénage où se trouve le pare-éclaboussures. À l'aide d'un tournevis à tête plate, retirez les (2) rivets poussoirs de la même zone. Retirez le pare-éclaboussures et remettez-le au propriétaire. ©2022 Horizon Global™ Corp. - Imprimé au Mexique Feuille 11 de 21...
  • Page 12 Retirez ensuite les (4) écrous du centre de l'écran thermique en utilisant la même douille. Retirez délicatement et mettez de côté pour une utilisation ultérieure. ©2022 Horizon Global™ Corp. - Imprimé au Mexique Feuille 12 de 21...
  • Page 13 à l'arrière du support, des deux côtés. Assurez-vous que l'attelage est bien droit avec l'emplacement marqué. Abaissez l'attelage et utilisez une perceuse pour percer un trou de ½ po, des deux côtés. Trous percés ©2022 Horizon Global™ Corp. - Imprimé au Mexique Feuille 13 de 21 76626NP 10-3-22 Rev.
  • Page 14 Figure 1 8. Réinstallez l'échappement et le capteur - Relevez l'échappement en position et fixez le capteur en place à l'aide du matériel d'origine retiré à l'étape 2. ©2022 Horizon Global™ Corp. - Imprimé au Mexique Feuille 14 de 21...
  • Page 15: Garantía Limitada De Por Vida

    TechnicalSupport@horizonglobal.com GARANTÍA LIMITADA DE POR VIDA Garantía limitada de por vida ("Garantía") Horizon Global ("nosotros", "nos" o "nuestro/a/s") Para evitar DAÑOS DE GRAVEDAD, A LA PROPIEDAD O LA MUERTE: garantiza al comprador original únicamente ("usted" o "su/s") que el producto estará libre de defectos significativos tanto en materiales como en mano de obra, con la excepción del desgaste...
  • Page 16: Equipo Necesario

    • Los tiempos de instalación se enumeran en los sitios web de Mercedes Horizon Global o se encuentran en las guías de aplicaciones descargables. *Visite nuestro sitio web para • Los niveles de dificultad de instalación se basan en el tiempo y la información más actualizada...
  • Page 17 Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York, V.E.S.C. Regulación V-5 y SAE J684. ©2022 Horizon Global™ Corp - Impreso en México Hoja 17 de 21...
  • Page 18 1. Retire el protector contra salpicaduras: con una llave de tubo de 10 mm, quite los (8) tornillos de la parte inferior de la fascia donde se encuentra el protector contra salpicaduras. Con un destornillador de cabeza plana, retire los (2) remaches de presión de la misma área. Retire el protector contra salpicaduras y devuélvalo al propietario. ©2022 Horizon Global™ Corp - Impreso en México Hoja 18 de 21 76626NP 10-3-22 Rev.
  • Page 19 3. Retire/recorte el escudo térmico/reinstale: a.) Con una llave de tubo de 8 mm, quite (2) tornillos de la parte inferior del vehículo (que se encuentran cerca del escape (1) por lado). Luego quite (4) tuercas del centro del escudo térmico usando el mismo dado. Retire con cuidado y reserve para su uso posterior. ©2022 Horizon Global™ Corp - Impreso en México Hoja 19 de 21...
  • Page 20 1.er orificio más atrasado, en ambos lados. Asegúrese de que el enganche quede derecho con la ubicación marcada. Baje el enganche y utilice un taladro para perforar un orificio de ½” en ambos lados. Orificios perforados ©2022 Horizon Global™ Corp - Impreso en México Hoja 20 de 21 76626NP 10-3-22 Rev.
  • Page 21 8. Vuelva a instalar el escape y el sensor: vuelva a colocar el escape en su posición y asegure el sensor en su lugar usando los accesorios originales que retiró en el paso 2. ©2022 Horizon Global™ Corp - Impreso en México...

Ce manuel est également adapté pour:

84626Cqt76626

Table des Matières