Publicité
ACCESSORIES
•
SKIL can assure flawless functioning of the tool only
when original accessories are used
•
Use only grinding/cutting discs with a maximum
thickness of 8 mm and a spindle hole diameter of
22 mm
•
For mounting/using non-SKIL accessories observe the
instructions of the manufacturer concerned
•
Never use reducors or adaptors to fit large-hole
grinding/cutting discs
•
Never use accessories with a "blind" threaded hole
smaller than M14 x 21 mm
OUTDOOR USE
•
Connect the tool via a fault current (FI) circuit breaker
with a triggering current of 30 mA maximum
BEFORE USE
•
Before using the tool for the first time, it is recommended
to receive practical information
Always check that the supply voltage is the same as the
•
voltage indicated on the nameplate of the tool
•
Always mount auxiliary handle E 2 and protective
guard F 2 ; never use the tool without them
•
Use suitable detectors to find hidden utility lines
or call the local utility company for assistance
(contact with electric lines can lead to fire or electrical
shock; damaging a gas line can result in an explosion;
penetrating a water pipe will cause property damage or
an electrical shock)
•
Do not work materials containing asbestos
(asbestos is considered carcinogenic)
•
Dust from material such as paint containing lead, some
wood species, minerals and metal may be harmful
(contact with or inhalation of the dust may cause allergic
reactions and/or respiratory diseases to the operator or
bystanders); wear a dust mask and work with a dust
extraction device when connectable
•
Certain kinds of dust are classified as carcinogenic
(such as oak and beech dust) especially in conjunction
with additives for wood conditioning; wear a dust
mask and work with a dust extraction device when
connectable
•
Follow the dust-related national requirements for the
materials you want to work with
•
Be careful when cutting grooves, especially in
supporting walls (slots in supporting walls are subject to
country-specific regulations; these regulations are to be
observed under all circumstances)
•
Secure the workpiece (a workpiece clamped with
clamping devices or in a vice is held more securely than
by hand)
•
Do not clamp the tool in a vice
•
Use completely unrolled and safe extension cords with a
capacity of 16 Amps (U.K. 13 Amps)
DURING USE
•
If the cord is damaged or cut through while working, do
not touch the cord, but immediately disconnect the plug
•
Never use the tool when cord is damaged; have it
replaced by a qualified person
•
In case of electrical or mechanical malfunction,
immediately switch off the tool and disconnect the plug
•
In case of current interruption or when the plug is
accidentally pulled out, immediately switch off the tool in
order to prevent uncontrolled restarting
AFTER USE
•
After switching off the tool, never stop the rotation of the
accessory by a lateral force applied against it
WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):
•
Do not connect the blue (= neutral) or brown (= live) wire
in the cord of this tool to the earth terminal of the plug
•
If for any reason the old plug is cut off the cord of
this tool, it must be disposed of safely and not left
unattended
USE
•
Mounting of accessories 2
! disconnect the plug
- clean spindle A and all parts to be mounted
- tighten clamping flange B with spanner C while
pushing spindle-lock button D
! push spindle-lock button D only when spindle A
is at a standstill
- for removing accessories handle vice-versa
! grinding/cutting discs become very hot during
use; do not touch them until they have cooled
down
! always mount backing pad when using sanding
accessories
! never use a grinding/cutting disc without
the label ("blotter") which is glued onto it (if
provided)
•
Mounting of auxiliary handle E 6
! disconnect the plug
- screw auxiliary handle E on the right or the left of the
tool (depending on the work to be carried out)
•
Adjusting of protective guard F 7
! disconnect the plug
! ensure that the closed side of the protective
guard always points to the operator
•
Removing of protective guard F 8
! disconnect the plug
- for mounting protective guard, handle in reverse order
•
Before using the tool
- ensure that accessory is correctly mounted and firmly
tightened
- check if accessory runs freely by turning it by hand
- test-run tool for at least 30 seconds at highest no-load
speed in a safe position
- stop immediately in case of considerable vibration or
other defects and check tool to determine the cause
•
On/off locking switch H 9
- switch on tool 9 a
! be aware of the sudden impact when the tool is
switched on
! before the accessory reaches the workpiece, the
tool should run at full speed
- lock switch 9 b
- unlock switch/switch off tool 9 c
! before switching off the tool, you should lift it
from the workpiece
! the accessory continues to rotate for a short time
after the tool has been switched off
•
Grinding q
- move the tool back and forth with moderate pressure
! never use a cutting disc for side grinding
•
Cutting w
- do not tilt the tool while cutting
- always move the tool in same direction as arrow on
tool head, in order to prevent the tool from being
pushed out of the cut in an uncontrolled manner
8
Publicité
