Hitachi CG 22EAS SL Mode D'emploi page 10
Masquer les pouces
Voir aussi pour CG 22EAS SL:
- Mode d'emploi (60 pages) ,
- Instructions de sécurité et mode d'emploi (64 pages) ,
- Mode d'emploi (68 pages)
Publicité
Les langues disponibles
Les langues disponibles
English
Engine
Displacement (cm
) (ml)
3
Spark plug
Idling speed (min
)
-1
Recommended max. speed (min
Speed of output shaft (min
Max. engine output (kW)
Fuel tank capacity (cm
) (ml)
3
Dry weight (kg)
Cutting attachment
Sound pressure
level LpA
(dB (A))
Measured sound
power level LwA
(dB (A))
Measured sound
power level LwA (dB (A))
Guaranteed sound
power level LwA (dB (A))
Vibration level (m/s
) (ISO7916)
2
Equivalent (Front / Left handle)
Equivalent (Rear / Right handle)
Idling (Front / Left handle)
Idling (Rear / Right handle)
Racing (Front / Left handle)
Racing (Rear / Right handle)
NOTE
Equivalent noise level/vibration level are calculated as the time-weighted energy total for noise/vibration levels under various working
conditions with the following time distribution: 1/2 Idle, 1/2 racing.
* All data subject to change without notice.
ASSEMBLY PROCEDURES
Drive shaft to engine (Fig. 1)
Loosen tube locking bolt (1) about ten turns so that the bolt point will
not obstruct drive shaft tube to be inserted. When inserting drive
shaft tube, hold the tube locking bolt outward preventing inside
fi tting from obstructing as well.
10
Model
CG24EASP (SL)
NGK BMR7A
)
-1
)
-1
Type / Dia. (mm)
Nylon cord
(ISO11806)
Equivalent
Uncertainty
(ISO11806)
Equivalent
Uncertainty
(2000/14/EC)
Racing
(2000/14/EC)
Racing
CG24EASP (S)
23.9
23.9
NGK BMR7A
3000
3000
11000
11000
9900
9900
0.85
0.85
4.6
4.9
Metal
Nylon
blade /
cord
230
92
92
3
3
105
105
105
3
3
107
107
107
108
108
108
6.2
3.7
3.7
5.8
4.7
4.7
4.2
2.6
2.6
3.1
4.4
4.4
7.7
4.6
11.6
7.6
5.0
8.2
Insert the drive shaft into the clutch case of the engine properly until
the marked position (2) on the drive shaft tube meets the clutch
case.
Some models may come with the drive shaft already installed.
NOTE
When it is hard to insert drive shaft up to the marked position on
the drive shaft tube, turn drive shaft by the cutter mounting end
clockwise or counter-clockwise. Tighten tube locking bolt lining
up the hole in the shaft tube. Then tighten clamp bolt securely.
CG27EASP (SL)
26.9
NGK BMR7A
3000
11000
9900
0.9
520
5.1
Nylon cord
93
93
3
3
107
3
3
108
109
6.2
7.4
3.1
2.0
8.3
10.4
CG27EASP (S)
26.9
NGK BMR7A
3000
11000
9900
0.9
5.3
Metal
Nylon
blade /
cord
230
93
95
3
3
107
107
3
3
108
108
109
110
4.8
8.6
4.0
6.1
2.8
2.8
3.9
3.9
6.2
11.9
4.1
7.6
Publicité
