Publicité
Les langues disponibles
Les langues disponibles
en
ENGLISH
7.4
Special working methods:
Cutting with parallel guide (fig. E)
1. If required, fit the wing screws (6):
Put the spring onto the thread, then screw in.
2. Push the parallel guide (7) into the grooves on
the base plate (12) and fix with the two wing
screws (6).
3. Loosen the wing screws (27) and roughly set the
desired distance between the stop bar of the
parallel guide and the cutter. Tighten the wing
screws (27).
4. Release the wing (29) screw. Finely adjust the
desired distance with the adjusting screw (28).
Tighten the wing screw (29).
If required, carry out a trial cut.
Template follower (Fig. F)
For cutting according to a template fixed on the
workpiece.
5. Insert the template follower (30) as shown and
fix with 2 short screws (a).
6. Attach a template (b) on the workpiece (c). Place
the machine on the template and guide it so that
the template follower (30) glides along the edge
of the template (b).
Milling from the workpiece edge.
1. Use routers with a thrust ring.
2. Release the clamping lever (4) and lower the
motor part of the switched-on router to the
desired milling depth.
3. To fix the milling depth, tighten the clamping
lever (4) and push the machine forward.
Milling along a strip attached to the workpiece
/ milling along a straight marking
1. Attach a strip on the workpiece and guide the
router with a straight edge of the foot plate along
the strip. (Always use the same edge.)
Mill grooves and fillets from the centre of the
workpiece
1. Release the clamping lever (4) and lower the
motor part of the switched-on router to the
desired milling depth.
2. To fix the milling depth, tighten the clamping
lever (4) and push the machine forward.
Profile milling
1. When working with profile cutters, first remove a
larger chip and then a smaller chip.
2. The feed rate must not be too low, otherwise the
wood will scorch and the cutter will become
prematurely blunt.
8. Cleaning, Maintenance
Remove battery pack.
Dust deposits must be regularly removed from the
machine. This includes vacuum cleaning the
ventilation louvres on the motor.
13
9. Troubleshooting
Electronic signal display (14) off, continuous
beeping, the machine is not running:
Restart protection:
Restart protection is active. The machine will not
start if the battery pack is inserted while the machine
is on. Switch the machine off and back on again.
Fast flashing, fast beeping, the machine was
switched off automatically:
Overload protection:
The overload protection protects the motor from
overheating. Switch the machine off and then on
again and continue to work with smaller feed or
reduced cutting depth.
Slow flashing, no beeping:
Battery pack almost empty: Charge the battery
pack soon.
Slow flashing, slow beeping:
Battery pack empty: Charge battery pack.
10. Accessories
Use only original Metabo or CAS (Cordless Alliance
System) battery packs and accessories.
Use only accessories that fulfil the requirements
and specifications listed in these operating
instructions.
Chargers: ASC 145, etc.
Battery packs with different capacities. Buy
battery packs only with voltage suitable for your
power tool.
4.0 Ah (LiHD), order no.: 625367000
5.5 Ah (LiHD), order no.: 625368000
etc.
5.2 Ah (Li-Ion), order no.: 625028000
etc.
For the complete range of accessories, see
www.metabo.com or the main catalogue.
11. Repairs
Repairs to electrical tools must only be carried
out by qualified electricians!
Contact your local Metabo representative if you
have Metabo power tools requiring repairs. For
addresses see www.metabo.com.
You can download a list of spare parts from
www.metabo.com.
12. Environmental Protection
Observe national regulations on environmentally
compatible disposal and on the recycling of disused
machines, packaging and accessories.
Packaging materials must be disposed of according
to their labelling in accordance with municipal
guidelines. Further information can be found at
www.metabo.com in the "Service" section.
Publicité
