BorMann PRO BBC2015 Manuel D'utilisation page 2

EN
Safety Instructions
Safety precautions for working in the vicinity of a battery
1. Batteries generate explosive gases during normal operation. Use in well-ventilated area.
2. Consider having someone close enough or within the range of your voice to come to your aid when you work near a battery.
3. Do NOT smoke, strike a match, or cause a spark in vicinity of battery or engine. Avoid explosive gas, flames and sparks.
4. Remove all personal jewellery, such as rings, bracelets, necklaces, and watches while working with a vehicle battery. These items may produce a short-circuit
that could cause severe burns.
5. Be extra cautious to reduce risk of dropping a metal tool onto the battery. It might spark or short-circuit a battery or other electrical hardware which may
cause an explosion or fire.
6. Wear complete eye protection, hand and clothing protection. Avoid touching eyes while working near a battery.
7. Study all battery manufacturer's specific precautions such as removing or not removing cell caps while charging and recommended rates of charge.
8. Clean battery terminals before connected with the charger. Be careful to keep corrosion from coming in contact with eyes.
9. When it is necessary to remove a battery from vehicle to charge, always remove grounded terminal from battery first. Make sure all accessories in the vehicle
are off in order to prevent an arc.
10. It is NOT intended to supply power to an extra-low-voltage electrical system or to charge dry-cell batteries. Charging dry-cell batteries may burst and cause
injury to persons and property.
11. NEVER charge a frozen, damaged, leaking or non-rechargeable battery.
12. If battery electrolyte contacts skin or clothing, wash immediately with soap and water. If electrolyte enters eye, immediately flood eye with running clean
cold water for at least 15 minutes and get medical attention immediately.
Safety precautions for using the charger
1. Do NOT place the charger in the engine compartment or near moving parts or near the battery; place as far away from them as DC cable permits. NEVER
place a charger directly above a battery being charged; gases or fluids from battery will corrode and damage charger.
2. Do NOT cover the charger while charging.
3. Do NOT expose to rain or wet conditions.
4. Connect and disconnect DC output only after setting AC cord from electric outlet.
5. Use of an attachment not recommended or sold by the manufacturer may result in a risk of fire, electric shock or injury to persons.
6. Do not overcharge batteries by selecting the wrong charge mode.
7. To reduce the risk of damage to electric plug and cord, pull by the plug rather than the cord when disconnecting charger.
8. To reduce risk of electric shock, unplug charger from outlet before attempting any maintenance or cleaning.
9. Operate with caution if the charger has received direct hit of force or been dropped. Have it checked and repaired if damaged.
10. Any repair must be carried out by the manufacturer or an authorized repair agent in order to avoid danger.
About BBC2015
1. The BBC2015 is designed for charging all types of 12V lead-acid and 24V lead-acid batteries, including WET (Flooded), MF (Maintenance-Free), EFB
(Enhanced Flooded Battery), GEL, AGM (Absorbed Glass Mat) batteries.
2. Built-in intelligent microprocessor makes charging faster, easier and safer.
3. This charger has safety features, including spark proof, protection for reverse polarity, short circuit, overheat and overcharge.
4. Automatically detect battery type (12V or 24V). Intelligent charging can be carried out without manual selection. The user can also manually select
battery type by pressing "12V" or "24V" button within the starting 10 seconds countdown (showed on the LCD). Once battery type has been selected
successfully and charging is started, you must disconnect the AC plug and plug in again if you want to change the battery type mode of the charger.
5. The starting charge current is 12V/5A or 24V/3.5A by default. You need press "CURRENT" button to choose the appropriate charge current for your
battery.
6. The charger LCD will show voltage (12V or 24V) and charge current in turn during normal charging process.
7. It shows present battery voltage (e.g. 12.1V) when "VOLTAGE" button is pressed.
8. Battery capacity is indicated by the "battery level icon". When the icon is in full status, do NOT break the connection immediately. It will automatically
switches from full charge to maintenance status without overcharging or damaging the battery.
Technical Data
Input:
Output:
Battery capacity:
Battery type:
Lowest Chargeable Voltage:
Housing protection:
* The manufacturer reserves the right to make minor changes to product design and technical specifications without prior notice unless these changes significantly affect the performance and safety of the
products. The parts described / illustrated in the pages of the manual that you hold in your hands may also concern other models of the manufacturer's product line with similar features and may not be
included in the product you just acquired.
* To ensure the safety and reliability of the product and the warranty validity, all repair, inspection, repair or replacement work, including maintenance and special adjustments, must only be carried out by
technicians of the authorized service department of the manufacturer.
* Always use the product with the supplied equipment. Operation of the product with non-provided equipment may cause malfunctions or even serious injury or death. The manufacturer and the importer
shall not be liable for injuries and damages resulting from the use of non-conforming equipment.
2
220-240VAC, 50/60Hz, 2.5A (700W MAX)
12VDC, 5/10/15/25A; 24VDC, 3.5/7.5/12A; 12VDC, 40A, 300s (Boost)
15-500AH(12V); 30-240AH(24V)
12/24V lead- acid batteries (WET/MF/CA/EFB/GEL/AGM)
3V
IP20
WWW.NIKOLAOUTOOLS.GR