Publicité
Les langues disponibles
Les langues disponibles
High Temp
Sani Rinse
Short Heated
Dry (Some
Models)
Short Power
Dry
Long Heated
Dry (Some
Models) Long
Power Dry
CONTROL
START
CANCEL
CONTROL
LOCK
FRONT
PANEL
INDICATOR
LIGHT
Cancelling a Cycle
1. Open the door slightly to stop the cycle. Wait for the
spraying action to stop before completely opening the door.
2. Press and hold START/Resume for 4 seconds. The
Cancel/Drain light will turn on.
3. Close the door, and the dishwasher starts a drain cycle
(if water remains in bottom of dishwasher). Let the
dishwasher drain completely. The Cancel/Drain light turns off
after 3 minutes.
Changing a Cycle After Dishwasher Is Started
You can interrupt a cycle and restart the dishwasher from the
beginning using the following procedure.
1. Open the door slightly to stop the cycle. Wait for the spraying
action to stop, then open the door completely.
2. Check that detergent dispenser cover is still closed. If cover is
open, you will need to refill the detergent dispenser before
restarting the new cycle.
OPTIONS
Helps remove tough, baked on food.
Sanitizes dishes and glassware in
accordance with NSF International
NSF/ANSI Standard 184 for Residential
Dishwashers. See this section in the
Owner's Manual.
Dries dishes with heat. Load plastic item
in upper racks.
Dries dishes with heat and a fan. Load
plastic item in upper racks.
Increases the Energy used for drying
the dishes. This may lengthen the cycle
time.
DISHWASHER FEEDBACK
PURPOSE
Press to start or resume a wash
cycle.
Press to cancel wash cycle.
Control Lock avoids unintended
use of dishwasher between cycles
or cycle and option changes
during a cycle.
On some models.
CAN BE
SELECTED
WHAT IT DOES
WITH
Increases main wash
temperature up to 135°F
Powerblast,
(54°C) to 140°F (60°C).
Auto,
Increases final rinse
Normal
temperature to 140°F
(60°C).
Increases main wash
temperature up to 140°F
Powerblast,
(60°C) to 140°F (60°C).
Auto,
Increases final rinse
Normal
temperature to 156°F
(69°C).
Powerblast,
Auto,
Dries dishes with heater
Normal,
or fan on some models.
Quick
Powerblast,
Dries dishes with heat or
Auto,
fan on some models.
Normal
COMMENTS
If the door is opened during a cycle or power is interrupted,
Start/Resume indicator light flashes. Cycle will not resume until
door is closed and START/Resume is pressed.
NOTE: Push door firmly closed within 4 seconds of pressing
START/Resume. If door is not closed within 4 seconds, the
Start/Resume button light will flash, an audible tone will be
heard, and cycle will not start.
Close door firmly. The dishwasher starts a 2 minutes drain
(if needed). Let dishwasher drain completely.
To turn on Lock, press and hold Heated Dry for 3 seconds.
Control Lock light will stay on, indicating that it is activated and
all buttons are disabled. If you press any button while your
dishwasher is locked, light flashes 3 times. Dishwasher door
can still be opened/closed while controls are locked.
To turn off Lock, press and hold Heated Dry for 3 seconds.
Light turns off.
Depending on the model, an indicator light on the front of the
door panel will glow green when a cycle is running and turns off
when the cycle is complete.
3. Press CANCEL/Drain to reset the control.
4. Select new cycles and options.
5. Press START/Resume.
Adding a Dish After Dishwasher is Started
1. Open the door slightly to stop the cycle. Wait for the
spraying action to stop, then open the door completely.
2. Check whether the detergent dispenser cover is still closed.
If it is open, the wash cycle has already started and adding a
dish is not recommended.
3. If detergent has not yet been used (detergent dispenser
cover is closed), you may add a dish.
4. Push door firmly closed and press START/Resume within
4 seconds. If you take too long, the Start keypad light
flashes, and you will hear an audible tone. Press
START/Resume again and close the door within 4 seconds.
ADDED
ADDED
TIME
WATER
TO
GALLONS
CYCLE
(LITERS)
0 to
0-1.4
0:45
(0-5.1 L)
0:10 to
0-2.3
1:15
(0-8.5 L)
0:33 to
NA
0:39
0:05 to
NA
0:20
Publicité
