Publicité
Les langues disponibles
Les langues disponibles
USING AIR CONDITIONER
For Cooling model
HIGH
MED
LOW
AUTO
SPEED
FAN
ECO
SPEED
FILTER
SLEEP
For Heating model
HIGH
MED
LOW
AUTO
SPEED
FAN
ECO
SPEED
FILTER
SLEEP
Air Conditioner Controls
Operating air conditioner properly helps you to obtain the best
possible results.
This section explains proper air conditioner operation.
IMPORTANT:
If you turn OFF the air conditioner, wait at least 3 minutes
■ ■
before turning it back on. This is to avoid the air conditioner
from blowing a fuse or tripping a circuit breaker.
Do not try to operate the air conditioner in the Cool mode
■ ■
when outside temperature is below 65°F (18°C). The inside
evaporator coil will freeze up, and the air conditioner will not
operate properly.
NOTE: In the event of a power failure, the air conditioner will
operate at the previous settings when the power is restored.
SPEED
Turning on the Air Conditioner
1. Press POWER to turn ON air conditioner.
2. Press POWER again to turn OFF the air
conditioner.
SPEED
Selecting the Mode
1. Press MODE button to cycle through the
various modes.
2. Choose modes: Cool, Dry, Fan, Auto or Heat.
Cool mode: The cooling function allows the air
■ ■
conditioner to cool the room and at the same
time reduces air humidity. Press the MODE
button to activate the cooling function. Press
the up or down arrow button to adjust the
temperature.
Dry Mode: This function reduces the humidity
■ ■
of the air to make the room more comfortable.
SPEED
Press MODE button to set the DRY mode. An
automatic function of alternating cooling cycles
and air fan is activated.
Fan Mode: In this mode, only fan runs to provide ventilation.
■ ■
Press MODE button to set the FAN mode. Press FAN SPEED
to select High, Med, or Low. The remote control stores the
SPEED
speed set in the previous mode of operation.
COOL
DRY
FAN
AUTO
MODE
MODE
POWER
TIMER
COOL
DRY
FAN
AUTO
MODE
HEAT
MODE
POWER
TIMER
MODE
MODE
MODE
MODE
Auto Mode: In AUTO mode, the unit automatically chooses
■ ■
the fan speed and the mode of operation (COOL, DRY or
FAN). In this mode the fan speed and the temperature are set
automatically according to the room temperature (tested by
the temperature sensor which is incorporated in the indoor
unit).
Heat Mode: The heating function allows the air conditioner to
■ ■
heat the room. Press the MODE button to activate the heating
function. To optimize the function of the air conditioner,
adjust the temperature and the speed by pressing the button
indicated.
NOTE: After 5 seconds, display will show the current room
temperature.
ECO Button: When the unit is in ECO mode,
■ ■
the light will turn ON. In ECO mode, the unit
will turn-off once the room is cooled to the
user set temperature. The fan motor will run
for 20 to 40 seconds and then it will stop, this will repeat
to provide more comfortable feeling and save energy. The
compressor will turn back on when the room temperature
rises above the set temperature. Press ECO to turn ECO
feature on and off. When the unit is in ECO mode, the light will
turn on.
SLEEP Button: Automatically adjusts the
■ ■
temperature and fan speed to make the room
more comfortable during the night. Press and
hold the SLEEP button for 10 seconds until the sleep light
turns on. All of the left lights will turn off. For heat mode,
temperature will automatically decrease by 1.8°F (1°C) every
30-60 minutes. At most, the temperature will change six
times until the temperature reaches 75°F (24°C). The set
temperature will automatically raise by 1.8°F (1°C) every 30-
60 minutes. At most, the temperature will change six times
until the temperature reaches 82°F (28°C). Running time
depends upon the set temperature.
NOTE: After 5 seconds, display will show the current room
temperature.
Selecting the Fan Speed
1. Press FAN SPEED button until the LED indicator
for the desired setting is lit.
2. Choose Low, Med, or High.
Low—Low fan speed
■
Med—Normal fan speed
■
High—Maximum fan speed
■
NOTES:
Auto fan speed and temperature cannot be
■ ■
selected in Fan Only mode.
In ECO and SLEEP modes, Auto fan speed is
■ ■
selected automatically.
After 5 seconds, the display will show the current
■ ■
room temperature.
AUTO
MODE
Adjusting the Temperature
HEAT
Press the up arrow button to increase the set
temperature.
Press the down arrow button to decrease the set
temperature.
NOTE: After 5 seconds, the display on the air
conditioner control panel will show the current room temperature.
Features
AUTO
SPEED
9
Publicité
