COOKTOP U SE
The surface cooking area will glow red when an element is on. It
may cycle on and off to maintain the selected heat level.
It is normal for the surface of white or biscuit ceramic glass to
appear to change color when surface cooking areas are hot. As
the glass cools, it will return to its original color.
Wiping off the cooktop before and after each use will help keep it
free from stains and provide the most even heating. On cooktops
with white or biscuit ceramic glass, soils and stains may be more
visible, and may require more cleaning and care. For more
information, see "General Cleaning" section.
•
Do not store jars or cans above the cooktop.
Dropping a
heavy or hard object onto the cooktop could crack the
cooktop.
Do not leave a hot lid on the cooktop. As the cooktop cools,
air can become trapped between the lid and the cooktop,
and the ceramic glass could break when the lid is removed.
For foods containing sugar in any form, clean up all spills and
soils as soon as possible. Allow the cooktop to cool down
slightly. Then, while wearing oven mitts, remove the spills
while the surface is still warm. If sugary spills are allowed to
cool down, they can adhere to the cooktop and can cause
pitting and permanent marks.
Do not slide cookware or bakeware across the cooktop.
Aluminum or copper bottoms and rough finishes on
cookware or bakeware could leave scratches or marks on the
cooktop.
Do not cook popcorn in prepackaged
aluminum containers
on the cooktop. They could leave aluminum marks that
cannot be removed completely.
Do not allow objects that could melt, such as plastic or
aluminum foil, to touch any part of the entire cooktop.
Do not use the cooktop as a cutting board.
Use cookware about the same size as the surface cooking
area. Cookware should not extend more than 1/2"(1.3 cm)
outside the area.
""
_-
"_ ........................
B
A. Surface cooking area
B. Cookware/canner
C. V2" (1.3 cm) Maximum overhang
Use flat-bottomed
cookware for best heat conduction and
energy efficiency. Cookware with rounded, warped, ribbed or
dented bottoms could cause uneven heating and poor
cooking results.
Determine flatness by placing the straight edge of a ruler
across the bottom of the cookware. While you rotate the ruler,
no space or light should be visible between it and the
cookware.
Cookware designed with slightly indented bottoms or small
expansion channels can be used.
Make sure the bottoms of pots and pans are clean and dry
before using them. Residue and water can leave deposits
when heated.
•
Do not cook foods directly on the cooktop.
When canning for long periods, alternate the use of surface
cooking areas, elements or surface burners between batches.
This allows time for the most recently used areas to cool.
•
Center the canner on the grate or largest surface cooking
area or element. On electric cooktops,
canners should not
extend more than 1/2"(1.3 cm) beyond the surface cooking
area or element.
•
Do not place canner on 2 surface cooking areas, elements or
surface burners at the same time.
•
On ceramic glass models, use only flat-bottomed
canners.
On coil element models, the installation of a Canning Unit Kit
is recommended.
If a kit is not installed, the life of the coil
element will be shortened. See "Assistance
or Service" for
ordering instructions.
•
For more information, contact your local agricultural
department. Companies that manufacture
home canning
products can also offer assistance.
IMPORTANT:
Do not leave empty cookware on a hot surface
cooking area, element or surface burner.
Ideal cookware should have a flat bottom, straight sides, and a
well-fitting
lid and the material should be of medium-to-heavy
thickness.
Rough finishes may scratch the cooktop. Aluminum
and copper
may be used as a core or base in cookware. However, when used
as a base they can leave permanent marks on the cooktop or
grates.
Cookware material is a factor in how quickly and evenly heat is
transferred, which affects cooking results. A nonstick finish has
the same characteristics
as its base material. For example,
aluminum cookware with a nonstick finish will take on the
properties of aluminum.
10