Publicité
Les langues disponibles
Les langues disponibles
Liens rapides
MATERIALS
A
1
Crossbar
B
2
Side arms
C
2
Bumper Shims
D
6
M14 x 40 x 2.0mm Bolts, Form A Washers and Nyloc Nuts
E
8
M12 x 40 x 1.25 Bolts 10.9 grade, Lock Washers and Flat Washers (25mm O.D.)
V
1
Retaining clip and Pin
Note: This towbar is to be used in conjunction with Reece couplings Z100
Please refer to vehicle specification for trailer weight and nose load limits, which must be observed.
FITTING
1. Remove the bumper
2. Remove the fixings securing the bumper arms to bumper and reattach using Bumper Shims (C) with original bolts and
fully tighten.
3.
Loosely attach side arms (B) to chassis rails using the forward 2 bolts (E), attach bumper using remaining Bolts (E).
4. Attach Cross bar (A) to side arms (B) using Bolts (D). Ensure a 10mm gap is achieved between Cross bar (A) and spare
wheel (spare wheel can moved forward easily by lowering slightly and pushing forward before tightening).
5. Make sure all components are aligned and fully tighten to recommended torques.
Recommended torque settings: Grade 8.8 bolts: M12 - 95 Nm, M14 - 150 Nm, M16 - 200 Nm Grade 10.9: M12 –
120Nm
Fitting
Instructions
For Toyota Hilux 2016-
Models Without Rectangular Underrun
TOWBAR
TY186/N
Bar
Publicité
Manuels Connexes pour Witter TY186/N
Sommaire des Matières pour Witter TY186/N
- Page 1 Fitting TOWBAR TY186/N For Toyota Hilux 2016- Instructions Models Without Rectangular Underrun MATERIALS Crossbar Side arms Bumper Shims M14 x 40 x 2.0mm Bolts, Form A Washers and Nyloc Nuts M12 x 40 x 1.25 Bolts 10.9 grade, Lock Washers and Flat Washers (25mm O.D.)
- Page 2 Notice de Attelage TY186/N Pour Toyota Hilux 2016- Modèles sans barre anti-encastrement montage rectangulaire Désignation Traverse principale Bras latéraux Entretoises de pare-chocs Boulons M14 x 100 x 2.0mm & écrous Nylocs Boulons M12 x 40 x 1.25 de Classe 10.9, Rondelles freins et rondelles plates Ø25mm Axe de maintien de la rotule Remarque: Cet attelage doit être utilisé...
- Page 3 Asennus- VETOKOUKKU TY186/N Toyota Hilux 2016- ohje Ajoneuvot ilman suorakaiteen muotoista alleajosuojaa ASENNUSSARJA Vetokoukun runko Sivukannake Puskurin kiinnike M14 x 40 x 2.0mm pultti, aluslevy ja Nyloc-mutteri M12 x 40 x 1.25 pultti (lujuusluokka 10.9) , lukitusaluslevy ja ø25mm aluslevy Sokkatappi ja jousisokka HUOM: Tätä...
- Page 4 Monterings- DRAGKROK TY186/N för Toyota Hilux 2016- Fordon utan rektangulär anvisning underkörningsbalk MONTERINGSSATS Dragets ramdel Sidojärn Stöd för stötfångare M14 x 40 x 2.0mm bult, bricka och Nyloc-mutter M12 x 40 x 1.25 bult (hållfasthetsklass 10.9) , låsbricka och ø25mm planbricka Tapp och fjädersprint...