Télécharger Imprimer la page

Publicité

Les langues disponibles

Les langues disponibles

Liens rapides

Fitting
Instructions
MATERIALS
A
1
Cross Bar.
B
1
Coupling Packer.
C
1
Left hand sidearm.
D
1
Right hand sidearm.
E
1
Left hand Chassis Stiffener.
F
1
Right hand Chassis Stiffener.
G
2
Spreader Plate (6mm).
H
6
M14 x 40 x 2.00 Bolts and Nyloc Nuts
K
12
M12 x 40 x 1.75 Bolts, Nyloc Nuts and 6 Flat washers 50mm O.D.
CB
2
M16 x 50mm Coupling Bolts, Nuts and Lock Washers.
Z
1
ZEP35 Electrical plate (not shown)
FITTING
1. Loosen bolts securing body to upper face of chassis sufficiently to allow slot in Chassis Stiffeners (E) and (F)
to be inserted, loosely attach to chassis using Bolts (K) with Flat Washers fitted as shown below.
2. Loosely secure Sidearms (C) and (D) to lower face of chassis using bolts (K) and Spreader Plate (G) as
shown below.
3. Loosely Attach Chassis Stiffeners (E) and (F) to Sidearms (C) and (D) using Bolts (K) with Flat Washers fitted
as shown below. (Note: on certain 29L models the chassis is reinforced with a double skin chassis, on these
vehicles Stiffeners (E) and (F) cannot be fitted and are not required – however where the double skin is not
present the ends of Chassis Stiffeners must be cut of to give sufficient clearance for vehicle cross brace-see
sketch below). Loosely attach Cross Bar (A) using Bolts (H) with towball as close to vehicle as possible.
4. Fully Tighten all bolts
NOTE: This towbar is EC type approved to be used with a Class A50-X towball with a 'D' Value greater than or equal to that of
the towbar. Please refer to the vehicle specification for the trailer weight and nose limits, which must be observed.
Recommended torque settings: M8 - 27Nm, M10 - 53 Nm, M12 - 95 Nm, M14 - 150 Nm, M16 - 214 Nm
WITTER TOWBARS
Deeside Ind. Park, Deeside, CH5 2NY
or vehicles fitted with a heavy duty step – secured to
witter-towbars.co.uk
W0001IV01-FIT$031103170000%Ä
W0001IV01-FIT$031103170000
For IVECO DAILY VANS
DOES NOT FIT vehicles with 172mm deep chassis
side and lower faces of chassis – use IV3 for these
IV1
TOWBAR
vehicles.
Issue 3

Publicité

loading

Sommaire des Matières pour Witter IV1

  • Page 1 Please refer to the vehicle specification for the trailer weight and nose limits, which must be observed. Recommended torque settings: M8 - 27Nm, M10 - 53 Nm, M12 - 95 Nm, M14 - 150 Nm, M16 - 214 Nm Issue 3 WITTER TOWBARS Deeside Ind. Park, Deeside, CH5 2NY witter-towbars.co.uk W0001IV01-FIT$031103170000%Ä...
  • Page 2 Châssis profond de 114mm Remarque : sur certains modèles 29L à revêtement simple, cette partie doit être enlevée pour libérer la traverse tubulaire du véhicule Avec marchepied Sans marchepied Edition 3 Support technique Numéro Vert : 0 805 102 860 WITTER TOWBARS...