Publicité
Les langues disponibles
Les langues disponibles
BM 2610034436 03-14_IDS181 3/27/14 11:22 AM Page 10
You will extend the life of your bits and do
neater work if you always put the bit in contact
with the work before pulling the trigger. During
the operation, hold the tool firmly and exert
light, steady pressure. Too much pressure at
low speed will stall the tool. Too little pressure
will keep the bit from cutting and cause
excess friction by sliding over the surface.
This can be damaging to both tool and bit.
DRIVING WITH VARIABLE SPEED
The technique is to start slowly, increasing the
speed as the screw runs down. Set the screw
snugly by slowing to a stop. Prior to driving
screws, pilot and clearance holes should be
drilled.
Always hold the machine straight on the bolt
to be tightened.
The best method to determine the right
impacting/tightening duration is by means of a
trial.
For
small
impacting/tightening duration can be reached
in less then 0.5 Sec. Therefore, work with low
RPM and switch the machine off immediately
when the screw is tight and the impacting
sound can be heard.
For screwing larger, longer wood screws into
hard material, pre-drilling is the best method.
TIGHTENING TORqUE
The tightening torque depends on the duration
of the impacting/tightening action. The largest
tightening torque is achieved after approx. 6 to
10 Sec. impacting/tightening action.
The torque build-up depends on the
following factors:
• Hardness of the bolts/nuts.
• Type of washer (disk washer, spring washer,
seal).
• Hardness of the material to be joined.
• Lubricating effect at the surfaces of the
junction.
This leads to the following application cases:
Hard case: The joining of metal to metal with
a disk washer. The maximum torque is
reached after a relative short impacting/
tightening action.
Medium case: The joining of metal to metal
where spring ring washer, disk spring washer,
stud bolts or bolts/nuts with conical seats are
used.
Operating Tips
screws,
the
right
-10-
Soft case: The joining of e.g. metal to wood
or insulation material.
For middle or soft joining cases, the maximum
tightening torque is less as for hard cases.
Therefore, a longer impacting/tightening
action is necessary to arrive at the maximum
tightening torque.
FASTENING WITH SCREWS
This procedure shown in (Fig. 5) will enable
you to fasten materials together with your tool
without stripping, splitting or separating the
material.
First, clamp the pieces together and drill the
first hole 2/3 the diameter of the screw. If the
material is soft, drill only 2/3 the proper
length. If it is hard, drill the entire length.
FASTENING
WITH SCREWS
1. Drill 2/3 diameter and
2/3 of screw length for
soft materials, full
length for hard
materials.
Apply a slight
even pressure
when driving
screws.
FIG. 5
Second, unclamp the pieces and drill the
second hole the same diameter as the screw
shank in the first or top piece of wood.
Third, if flat head screw is used, countersink
the hole to make the screw flush with the
surface. Then, simply apply even pressure
when driving the screw. The screw shank
clearance hole in the first piece allows the
screw head to pull the pieces tightly together.
RUNNING NUTS AND BOLTS
Variable speed control must be used with
caution for driving nuts and bolts with socket
set attachments. The technique is to start
slowly, increasing speed as the nut or bolt runs
down. Set the nut or bolt snugly by slowing the
tool to a stop. If this procedure is not followed,
the tool will have a tendency to torque or twist
in your hands when the nut or bolt seats.
2. Drill same
diameter as
screw shank.
3. Countersink
same diameter
as screw head.
Screw
Publicité
