Control Panel Indicators; Pressure Relief Procedure - Titan RENTSPRAY 600 Notice D'utilisation

12. Trigger the gun into the metal waste container until all air
and solvent is flushed from the spray hose and paint is
flowing freely from the gun.
13. Lock the gun by turning the gun trigger
lock to the locked position.
14. Turn off the sprayer.
15. Attach tip guard and tip to the gun
as instructed by the tip guard or tip
manuals.
POSSIBLE INJEcTION haZaRD.
Do not spray without the tip guard in place. Never
trigger the gun unless the tip is in either the spray or
the unclog position. always engage the gun trigger
lock before removing, replacing or cleaning tip.
16. Turn on the sprayer.
17. Increase the pressure by turning the pressure control
knob slowly clockwise and test the spray pattern on a
piece of cardboard. Adjust the pressure control knob until
the spray from the gun is completely atomized. Try to
keep the pressure control knob at the lowest setting that
maintains good atomization.
NOTE: Turning the pressure up higher than needed to
atomize the paint will cause premature tip wear
and additional overspray.

control Panel Indicators

The following is a description of the control panel indicators.
Motor
Running
Indicator
RAPID
CLEAN
Pressure Indicator
The pressure indicator shows the current operating pressure of
the sprayer. It has three different indications: blinking yellow,
solid yellow, and solid green.
Blinking Yellow
When the pressure indicator is blinking yellow, the sprayer is
operating between 0 and 200 PSI. A blinking yellow pressure
indicator means:
• The sprayer is plugged in and turned "ON"
• The sprayer is at priming pressure (little or no pressure)
• It is safe to move the PRIME/SPRAY valve between
positions
• It is safe to change or replace the spray tip
NOTE: If the pressure indicator begins blinking yellow
when the pressure control knob is set at a
higher pressure and the PRIME/SPRaY valve
is in the SPRaY position, either the spray tip is
worn or the sprayer is in need of service/repair.
Solid Yellow
When the pressure indicator is solid yellow, the sprayer is
operating between 201 and 1900 PSI. A solid yellow pressure
indicator means:
English
• The sprayer is at the proper pressure setting for spraying
• If the pressure indicator goes to solid yellow when the
Trigger lock in
locked position.
Solid Green
When the pressure indicator is solid green, the sprayer is
operating between 1901 and 3300 PSI. A solid green pressure
indicator means:
• The sprayer is at the proper pressure setting for spraying
• The sprayer is operating at peak performance at a high
Motor Running Indicator
The Motor Running indicator is on when the motor is commanded
to run. This indicator is used by service centers to troubleshoot
motor problems.

Pressure Relief Procedure

Pressure
Indicator
1. Lock the gun by turning the gun trigger
2. Turn off the sprayer by moving the ON/
3. Turn the pressure control knob
4. Unlock the gun by turning the gun trigger lock to the
5. Hold the metal part of the gun firmly
6. Trigger the gun to remove any
7. Lock the gun by turning the gun trigger lock
8. Move the PRIME/SPRAY valve down to
6
stain, lacquer, varnish, and multi-colors
pressure is set so that it starts at solid green, it indicates
one of the following:
a. Tip Wear Indicator — when spraying with latex or at
high pressure the solid yellow appears. This means the
tip is worn and needs to be replaced.
b. Tip Too Large — when a tip that is too large for the
sprayer is put in the gun, the pressure indicator will turn
from solid green to solid yellow.
c. Fluid Section Wear — if a solid yellow pressure
indicator appears when using a new tip and the pressure
is set at maximum, service may be required (worn
packings, worn piston, stuck valve, etc...).
oil-based and latex house paints
pressure setting
Be sure to follow the pressure relief procedure
when shutting the unit down for any purpose,
including servicing or adjusting any part of the
spray system, changing or cleaning spray tips, or
preparing for cleanup.
lock to the locked position.
OFF switch to the OFF position.
counterclockwise to its OFF position in
the black zone.
unlocked position.
to the side of a metal container to
ground the gun and avoid a build up
of static electricity.
pressure that may still be in the hose.
to the locked position.
the PRIME position.
© Titan Tool Inc. All rights reserved.
Trigger lock in
locked position.