Publicité
Les langues disponibles
Les langues disponibles
Installation
■
Do not look directly into the LED light. This
can cause damage to the eyes.
5 INSTALLATION
WARNING! Danger if assembly is not
carried out completely! Use of an incompletely
assembled appliance can result in serious injury.
■
Operate the appliance only when it is fully as-
sembled!
■
Do not insert the battery into the appliance
until it is fully assembled!
5.1
Unpacking the machine
1. Remove all parts from the packaging.
2. Check that all parts have been delivered (see
chapter 3.3 "Scope of supply", page 23).
3. Check all parts for transport damage.
If any damage is evident or parts are missing,
immediately inform the dealer where the ap-
pliance was purchased.
5.2
Mounting the lower brace (02)
1. Position both ends of the lower brace (02/1)
against the pipe ends (02/2) (02/a) in such a
way that the insertion holes of the lower
brace and the pipe ends line up.
2. Insert two long locking screws (02/3) from the
inside.
3. Place a washer (02/4) on each of the locking
screws.
4. Screw star handles (02/5) onto the locking
screws and firmly tighten.
5.3
Mounting the intermediate brace (03)
1. Push both ends of the intermediate brace
(03/1) onto the lower brace (03/2) (03/a) in
such a way that the insertion holes of the in-
termediate brace and lower brace line up.
The guide (03/3) for the adjusting crank must
point upwards.
2. Insert two long locking screws (03/4) from the
inside.
3. Place a washer (03/5) on each of the locking
screws.
4. Screw star handles (03/6) onto the locking
screws and firmly tighten.
5.4
Mounting the upper brace (04)
1. Push both ends of the upper brace (04/1) on-
to the intermediate brace (04/2) (04/a) in
such a way that the insertion holes of the up-
per brace and intermediate brace line up.
469905_f
The motor switch, motor switch bracket, han-
dle and LED light must point upwards.
2. Insert two long locking screws (04/3) from the
inside.
3. Place a washer (04/4) on each of the locking
screws.
4. Screw star handles (04/5) onto the locking
screws and firmly tighten.
5.5
Fixing the cables to the bar (05)
1. Fix the cable (05/1) of the motor switch with a
cable holder (05/2) to the intermediate brace
and to the lower brace.
2. Fix the cable (05/3) of the LED light with a
cable holder (05/2) to the intermediate brace
and to the lower brace.
5.6
Installing the adjustment crank (06, 07)
Connecting the adjustment crank to the
extension shaft (06)
1. Insert the adjusting crank (06/1) through the
guide (06/2) onto the intermediate brace (06/
a) from above.
2. Insert the adjustment crank into the support
(06/3) of the extension shaft up to the end
stop (06/b).
3. Align the adjusting crank and the extension
shaft so that their holes line up.
4. Push a cotter pin (06/4) through both bores
(06/c) until it clicks into place.
Installing and fixing the adjustment crank
onto the appliance (07)
1. Insert the extension shaft (07/1) into the
mounting (07/2) on the appliance (07/a).
2. Rotate the extension shaft so that its hole
and the hole of the mounting line up.
3. Push a cotter pin (07/3) through both bores
(07/b) until it clicks into place.
4. Turn the star handle (07/4) onto the guide
(07/5) and slightly tighten it to fix the adjust-
ment crank in place.
5.7
Installing the snow deflector (08)
1. Place the snow deflector (08/1) on the ejec-
tion channel (08/2) (08/a) so that the lugs
(08/3) engage in the recesses of the snow
deflector on the left and right.
2. Insert each of the two short carriage bolts
(08/4) through the holes of the ejection chan-
nel from the inside (08/b).
27
Publicité
