F.F. Group ELM 38/1600 PLUS Notice Originale page 12

12 | English
TECHNICAL DATA
Article Number
ELM 38/1600
Model
Rated voltage V
Rated
Hz
frequency
Propulsion
system
Cutting width cm
Cutting height
mm
(6 positions)
range
Mulching plug
Rated power W
Grass bag
L
capacity
Front wheel
mm
diameter
Rear wheel
mm
diameter
Cable length cm
Vibration
m/s
2
level (ah)
Uncertainty (K) m/s
2
Sound power
dB(A)
level (LwA)
Guaranteed
sound power dB(A)
level (LwA)
Uncertainty (K) dB
Net Weight kg
IDENTIFICATION (Fig. 1)
1. ON/OFF switch lever
2. Upper handle
3. Extension cord restraint hook
4. Appliance cord
5. Grass collector handle
6. Quick release lever
7. Grass collector
8. Handle frame knob
9. Rear wheel
10. Front wheel
11. Height adjustment lever
12. Lower handle
13. Cable clip
14. Switch box
15. Safety button
46 521 46 522
ELM 43/1800
PLUS PLUS
230-240 230-240
50 50
Push Push
38 43
25-75 25-75
(6 positions)
Yes Yes
1.600 1.800
40 50
150 170
200 240
35 35
3,5 4,5
1,5 1,5
94 93
95,9 96
1,85 3
13 16,5
ELM 38/1600 PLUS | ELM 43/1800 PLUS
ASSEMBLY
HANDLE ASSEMBLY
1. On each side of the lawn mower, place the handle
frame (Fig. 2.1), place the washer (Fig. 2.2) and tight-
en the assembly securely with the knob (Fig. 2.3).
2. Place the adapter (Fig. 3.2) in position on han-
dle frame (Fig. 2.1), place the upper handle (Fig.
3.6) on the adapter's grove and tighten secure-
ly using the bolt (Fig. 3.1), the washer (Fig. 3.5)
and the quick release handle assembly (Fig. 3.3,
3.4).
NOTE
Where applicable, make sure to place the extension
cord restraint hook (Fig. 1.3) in position on the upper
handle before step "2".
GRASS COLLECTOR ASSEMBLY AND FITTING
The grass collector (Fig. 1.7) prevents grass clip-
pings being thrown across your lawn as you mow.
1. Insert the grass collector handle (Fig. 4.1) into
the holes on the top of grass collector (Fig. 4.2)
until it clicks in position.
2. Align the upper and lower grass collector sec-
tions and join. Ensure the clips are located cor-
rectly and securely.
NOTE
For models with plastic lower part, join before-
hand the left and right side together in one piece
(Fig. 4.3).
NOTE
For models with fabric lower part, insert the sup-
port (Fig. 4.4) in place afterwards.
3. Lift the collector flap with one hand. With the
other hand hold the grass collector by the han-
dle and hook it in from above (Fig. 5).
OPERATION
WARNING
Before connecting to the mains supply, always check
the switch is in the off position!
EXTENSION CORD RESTRAINT
We recommend using your mower as outlined in
this section to achieve optimum results and to re-
duce the risk of cutting the mains cable. Place the
bulk of the mains cable on the lawn, close to the
starting point. Feed the cable through the cable
restraint (Fig. 1.3).
ADJUSTING THE CUTTING HEIGHT
This electric lawn mower is equipped with a 6-po-
sition height adjustment system to tailor grass
cutting heights of 25 to 75mm. To obtain your de-
sired cutting height, the front and rear axles are
repositioned on the underside of the lawnmower
body. Adjust using the height adjuster handle (Fig.
1.11) to the desired height.
STARTING THE MOTOR
1. Plug the machine into the electric supply, en-
suring it meets the recommended require-
ments. Electrical power should be supplied via
a residual current device (RCD) with a tripping