Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
1.
DANGER!:
Keep hands away from cutting area and blade. Keep your second
hand on auxiliary handle or motor housing. If both hands are holding
the saw, they cannot be cut by the blade.
Do not reach underneath the workpiece. The guard cannot protect
you from the blade below the workpiece.
Adjust the cutting depth to the thickness of the workpiece. Less
than a full tooth of the blade teeth should be visible below the work-
piece.
NEVER hold piece being cut in your hands or across your leg.
Secure the workpiece to a stable platform. It is important to support
the work properly to minimize body exposure, blade binding, or loss of
control.
Hold power tool by insulated gripping surfaces when performing
an operation where the cutting tool may hidden wiring or its own
cord. Contact with a "live" wire will also make exposed metal parts of
the tool "live" and shock the operator.
When ripping always use a rip fence or straight edge guide. This
improves the accuracy of cut and reduces the chance of blade bind-
ing.
Always use blades with correct size and shape (diamond versus
round) of arbor holes. Blades that do not match the mounting hardware
of the saw will run eccentrically, causing loss of control.
Never use damaged or incorrect blade washers or bolts. The blade
washers and bolts were specially designed for your saw, for optimum
performance and safety of operation.
2.
Causes and Operator Prevention of KICKBACK:
KICKBACK is a sudden reaction to a pinched, bound or misaligned saw
blade, causing an uncontrolled saw to lift up and out of the workpiece
toward the operator.
When the blade is pinched or bound tightly by the kerf closing down, the
blade stalls and the motor reaction drives the unit rapidly back toward
the operator.
If the blade becomes twisted or misaligned in the cut, the teeth at the
back edge of the blade can dig into the top surface of the wood causing
the blade to climb out of the kerf and jump back toward operator.
KICKBACK is the result of saw misuse and/or incorrect operating pro-
cedures or conditions and can be avoided by taking proper precautions
as given below:
Maintain a fi rm grip with both hands on the saw and position your
arms to resist kickback forces. Position your body to either side of the
blade, but not in line with the blade. Kickback could cause the saw to
jumb backwards, but kickback forces can be controlled by the operator,
if proper precautions are taken.
When blade is binding, or when interrupting a cut for any reason,
release the trigger and hold the saw motionless in the material
until the blade comes to a complete stop. Never attempt to remove
the saw from the work or pull the saw backward while the blade
is in motion or kickback may occur. Investigate and take corrective
actions to eliminate the cause of blade binding.
When restarting a saw in the workpiece, center the saw blade in
the kerf and check that saw teeth are not engaged into the material.
If saw blade is binding, it may walk up or kickback from the workpiece
as the saw is restarted.
Support large panels to minimize the risk of blade pinching and
kickback. Large panels tend to sag under their own weight. Supports
must be placed under the panel on both sides, near the line of cut and
near the edge of the panel.
Do not use dull or damaged blade. Unsharpened or improperly set
blades produce narrow kerf causing excessive friction, blade binding
and kickback.
Blade depth and bevel adjusting locking levers must be tight and
secure before making cut. If blade adjustment shifts while cutting, it
may cause binding and kickback.
Use extra caution when making a "plunge cut" (or pocket cut) into
existing walls or other blind areas. The protruding blade may cut
objects that can cause kickback.
page 4
SPECIFIC SAFETY RULES - FOR METAL CUTTING SAWS
3.
Check lower guard for proper closing before each use. Do not op-
erate saw if lower guard does not move freely and close instantly.
Never clamp or tie the lower guard into the open position. If saw is
accidentally dropped, lower guard may be bent. Raise the lower guard
with the lower guard lever and make sure it moves freely and does not
touch the blade or any other part, in all angles and depths of cut.
Check the operation of the lower guard spring. If the guard and the
spring are not operating properly, they must be serviced before
use. Lower guard may operate sluggishly due to damaged parts, gummy
deposits, or a buildup of debris.
Lower guard should be retracted manually only for special cuts
such as "plunge cuts" ("pocket cuts") and "compound cuts". Raise
lower guard by lower guard lever and as soon as blade enters the
material, the lower guard must be released. For all other sawing,
the lower guard should operate automatically.
Always observe that the lower guard is covering the blade before
placing saw down on bench or fl oor. An unprotected, coasting
blade will cause the saw to walk backwards, cutting whatever is in its
path. Be aware of the time it takes for the blade to stop after switch is
released.
4.
Maintain labels and nameplates. These carry important information.
If unreadable or missing, contact a MILWAUKEE service facility for a
free replacement.
5.
WARNING! Some dust created by power sanding, sawing, grinding,
drilling, and other construction activities contains chemicals known to
cause cancer, birth defects or other reproductive harm. Some examples
of these chemicals are:
• lead from lead-based paint
• crystalline silica from bricks and cement and other masonry products,
and
• arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on how often you do
this type of work. To reduce your exposure to these chemicals: work in
a well ventilated area, and work with approved safety equipment, such
as those dust masks that are specially designed to fi lter out microscopic
particles.
6.
Do not touch material immediately after it has been cut. Use cau-
tion; cut material may be hot and sharp.
7.
Do not use cutting oil. The use of cutting oil may cause a fi re.
8.
Do not use tool near fl ammable material. Sparks may cause fi re.
9.
Chip container cover may be hot after use. Use caution when empty-
ing chip container or changing the blade.
10. Do not start the blade when in contact with workpiece. Wait for
blade to reach full speed before beginning cut.
Publicité
Table des Matières
