Bosch 06033B2402 Notice Originale page 14

14 | English
(1) Saw blade
(2) Base plate
(3) Saw blade receptacle
(4) Locking sleeve for saw blade
(5) Battery charge indicator
(6) On/off switch
(7) Lock-off button for on/off switch
(8) Battery release button a)
(9) Battery a)
(10) Handle (insulated gripping surface)
a) Accessories shown or described are not included with the
product as standard. You can find the complete selection of
accessories in our accessories range.
Technical data
Reciprocating saw
Article number
Stroke rate control
Rated voltage
No-load stroke rate n
0
Tool holder
Stroke
Max. cutting depth
– in wood
– in steel (unalloyed)
– Pipe diameter
Weight according to
EPTA‑Procedure 01:2014 A)
Recommended ambient
temperature during char-
ging
Permitted ambient temper-
ature during operation B) and
during storage
Recommended re-
chargeable batteries
Recommended battery
chargers C)
A) Depends on battery in use
B) Limited performance at temperatures < 0 °C
C) The following chargers are not compatible with the PBA re-
chargeable battery: AL 1814 CV, AL 1820 CV, AL 1860 CV
Noise/vibration information
Noise emission values determined according to
EN 62841‑2‑11.
Typically, the A-weighted noise level of the power tool is:
Sound pressure level 88 dB(A); sound power level
99 dB(A). Uncertainty K = 5 dB.
Wear hearing protection!
1 609 92A 7KW | (24.06.2022)
AdvancedRecip 18
3 603 CB2 4..
●
V= 18
min −1 0–3100
SDS
mm 23
mm 100
mm 20
mm 20
kg 2.3 (1.5 Ah) to
2.6 (6.0 Ah)
°C 0 to +35
°C –20 to +50
PBA 18V...W-.
AL 18...
Vibration total values a (triax vector sum) and uncertainty K
h
determined according to EN 62841‑2‑11:
Cutting boards with saw blade S 644 D:
a = 12.6 m/s 2 , K = 1.5 m/s 2 ,
h,B
Cutting wooden beams with saw blade S 3456 F:
a = 13.1 m/s 2 , K = 1.5 m/s 2 .
h,WB
The vibration level and noise emission value given in these
instructions have been measured in accordance with a
standardised measuring procedure and may be used to com-
pare power tools. They may also be used for a preliminary
estimation of vibration and noise emissions.
The stated vibration level and noise emission value repres-
ent the main applications of the power tool. However, if the
power tool is used for other applications, with different ap-
plication tools or is poorly maintained, the vibration level
and noise emission value may differ. This may significantly
increase the vibration and noise emissions over the total
working period.
To estimate vibration and noise emissions accurately, the
times when the tool is switched off or when it is running but
not actually being used should also be taken into account.
This may significantly reduce vibration and noise emissions
over the total working period.
Implement additional safety measures to protect the oper-
ator from the effects of vibration, such as servicing the
power tool and application tools, keeping their hands warm,
and organising workflows correctly.
Rechargeable battery
Bosch sells some cordless power tools without a re-
chargeable battery. You can tell whether a rechargeable bat-
tery is included with the power tool by looking at the pack-
aging.
Charging the battery
Use only the chargers listed in the technical data. Only
u
these chargers are matched to the lithium-ion battery of
your power tool.
Note: Lithium-ion rechargeable batteries are supplied par-
tially charged according to international transport regula-
tions. To ensure full rechargeable battery capacity, fully
charge the rechargeable battery before using your tool for
the first time.
Inserting the Battery
Push the charged battery into the battery holder until it
clicks into place.
Removing the Battery
To remove the rechargeable battery, press the battery re-
lease button and pull the battery out. Do not use force to do
this.
Battery charge indicator
The battery charge indicator indicates the state of charge for
a few seconds when the on/off switch is half or fully pressed.
Bosch Power Tools