Publicité
14
921A OSCILLATOR DRIVER
921A OSCILLATOR DRIVER Controls
(CN) 控制
FREQUENCY –
(1)
置连接到
的频率。
SEMITONE/OCTAVE –
(2)
翘板开关在
的半音或八度增量之间进
行选择。
WIDTH OF RECTANGULAR WAVE
(3)
–
在
间选择。
CONTROL INPUT/FREQUENCY
(4)
–
通过带有
器的电缆， 将频率的输入控
制电压信号连接到这些双重
求和输入插孔。 这两个控制
输入也与
钮相加。
CONTROL INPUTS/WIDTH –
该旋钮手动设
(5)
921A
3.5
模块的振荡器
通过带有
毫米
的电缆， 将输入信号的矩形
波宽度的控制电压
使用此
连接到这些双重求和插孔。
FREQUENCY
旋钮
这两个控制输入也与
旋钮相加。
CONTROL OUTPUTS TO 921B –
(6)
将控制信号连接到
10
90
％ 到
％ 的设置之
模块。 左输出插孔用于频率
控制信号， 并连接到
率链接插孔之一。 右侧输出
插孔用于矩形波宽度控制信
3.5
TS
毫米
连接
921B
号， 并连接到
插孔之一。 然后可以将
上的辅助并行链接插孔链接
921B VCO
到其他
FREQUENCY
控制旋
921A
驱动器最多可以驱动十
921B
二个
模块。
Power Connection
P1
Red Stripe
2
1
TS
连接器
/
调制信号
10
9
WIDTH
921B VCO
Connect end P1 to the module socket
Connect end P2 to the power supply
921B
频
The 921A OSCILLATOR DRIVER module comes with the required power cable for connecting to a standard Eurorack power
宽度链接
supply system. Follow these steps to connect power to the module. It is easier to make these connections before the
921B
module has been mounted into a rack case.
模块， 并且
1.
Turn the power supply or rack case power off and disconnect the power cable.
2.
Insert the 16-pin connector on the power cable into the socket on the power supply or rack case. The connector has a
tab that will align with the gap in the socket, so it cannot be inserted incorrectly. If the power supply does not have a
keyed socket, be sure to orient pin 1 (-12 V) with the red stripe on the cable.
3.
Insert the 10-pin connector into the socket on the back of the module. The connector has a tab that will align with
the socket for correct orientation.
4.
After both ends of the power cable have been securely attached, you may mount the module in a case and turn on
the power supply.
Installation
The necessary screws are included with the module for mounting in a Eurorack case. Connect the power cable
before mounting.
Depending on the rack case, there may be a series of fixed holes spaced 2 HP apart along the length of the case, or a track
that allows individual threaded plates to slide along the length of the case. The free-moving threaded plates allow precise
positioning of the module, but each plate should be positioned in the approximate relation to the mounting holes in your
module before attaching the screws.
Hold the module against the Eurorack rails so that each of the mounting holes are aligned with a threaded rail or threaded
plate. Attach the screws part way to start, which will allow small adjustments to the positioning while you get them all
aligned. After the final position has been established, tighten the screws down.
P2
1
2
HOT USED
15
16
+ 12V
200 mm ± 10
GROUND
- 12V
15
Quick Start Guide
+ 12V
GROUND
- 12V
Publicité
