Publicité
ARTICLE 5 = M6 ÉCROUS (x2)
ARTICLE 6 = M6 RONDELLE (19mm OD) (x1)
ARTICLE 7 = M6 RONDELLE (16mm OD) (x1)
Page | 4
NOTICE DE MONTAGE
Positionner la rondelle M6 (article 6) et un écrou M6 (article 5) sur chaque extrémité filetée de l'axe de moyeu
(article 3). Veiller à ce que l'écrou soit complètement engage sur le filetage.
Placer la bobine (article 4) suivie d'un bloc de montage (article 1) sur l'axe, de façon à ce que l'écrou et la
rondelle se placent dans le contre alésage de la bobine. Positionnez la dans le moyeu arrière du côté gauche de la
moto, en veillant à ce que le bloc de montage se place sur l'écrou d'axe.
Monter le cache moyeu du côté droit (article 2) dans le trou du côté droit de la roue en veillant à ce que l'axe de
moyeu dépasse du cache moyeu.
Insérer la rondelle restante (article 7) et l'écrou (article 5) sur le filetage exposé de l'axe de moyeu puis serrer.
Veiller à ce que l'ensemble corresponde au schéma présenté en page 1. Serrer complètement les écrous des 2
côtés. Ne pas trop serrer – les écrous fixent l'ensemble.
The catalogue description and any exhibition of samples are only broad indications of the Products and R&G may make design changes which do not
diminish their performance or visual appeal and supplying them in such state shall conform to the order. The Buyer acknowledges no representation or
warranty (other than as to title) has been given or will apply to the Products other than those in R&G's order or confirmation and the Buyer confirms it
has chosen the Products as being of merchantable quality and suitable for its particular purposes. Where R&G fits the Products or undertakes other
services it shall exercise reasonable skill and care and rectify any fault free of charge unless the workmanship has been disturbed. The Buyer is
responsible for ensuring that the warranty on the motorcycle is not affected by the fitting of the Products. On return of any defective Products R&G
shall at its option either supply a replacement or refund the purchase money but shall not be liable if the Products have been modified or used or
maintained otherwise than in accordance with R&G's or manufacturer's instructions and good engineering practice or if the defect arises from accident
or neglect. Other than identified above and subject to R&G not limiting its liability for causing death and personal injury, it shall not be liable for
indirect or consequential loss and otherwise its liability shall be limited to the amounts paid by the Buyer for the Products or the fitting or service
concerned. These terms do not affect the Buyer's statutory rights.
Returns must be pre-authorised (if not pre-authorised the return will be rejected). Goods may only be returned direct to us if they were purchased direct
from us (customer must prove if necessary). Otherwise to be returned to original vendor. Goods must be in re-sellable condition, in the opinion of
R&G. All returns are subject to a 25% restocking and handling fee (25% of the gross value exc. P&P – at the prevailing price at time of purchase). The
customer must pay any and all carriage charges. No returns of discontinued products, unless within 14 days of purchase. This policy does not affect your
statutory rights and does not refer to faulty goods.
Tel: +44 (0)1420 89007 Fax: +44 (0)1420 87301
OUTILS REQUIS
Clé à cliquet + douilles 10mm (x2).
V
ALEURS DE SERRAGE RECOMMANDEES
M4 BOULON = 8Nm
M5 BOULON = 12Nm
M6 BOULON = 15Nm
M8 BOULON = 20Nm
M10 BOULON = 40Nm
ISSUE 14/08/2018 (HB)
Notice disponible au téléchargement sur
CONSUMER NOTICE
R&G RETURNS POLICY (NON-FAULTY GOODS)
Unit 1, Shelley's Lane, East Worldham, Alton, Hampshire, GU34 3AQ
www.rg‐racing.com
R&G
www.rg-racing.com
Email:
SP0082
info@rg-racing.com
Publicité
