Bosch GWS 27-230 Professional Notice Originale page 13

For best results when cutting stone, use a diamond cutting
disc.
When using the extraction guard for cutting with a guide
block (21), the vacuum cleaner must be approved for vacu-
uming stone dust. Suitable vacuum cleaners are available
from Bosch.
Switch on the power tool and position
it with the front part of the guide block
on the workpiece. Move the power
tool with a moderate feed motion that
is suited to the material being ma-
chined.
When cutting especially hard materi-
als such as concrete with a high
pebble content, the diamond cutting disc can overheat and
become damaged as a result. This is clearly indicated by cir-
cular sparking, rotating with the diamond cutting disc.
If this happens, stop cutting and allow the diamond cutting
disc to cool down by running the power tool for a short time
at maximum speed with no load.
Working noticeably slower and with circular sparking indic-
ate that the diamond cutting disc that has become dull. You
can resharpen the disc by briefly cutting into abrasive mater-
ial (e.g. lime-sand brick).
Information on structural design
Recesses in load-bearing walls are subject to country-spe-
cific regulations. These regulations must be observed under
all circumstances. Seek advice from the responsible struc-
tural engineer, architect or construction supervisor before
starting work.
Maintenance and Service
Maintenance and Cleaning
Pull the plug out of the socket before carrying out any
u
work on the power tool.
To ensure safe and efficient operation, always keep
u
the power tool and the ventilation slots clean.
In order to avoid safety hazards, if the power supply cord
needs to be replaced, this must be done by Bosch or by an
after-sales service centre that is authorised to repair Bosch
power tools.
Store and handle the accessories carefully.
After-Sales Service and Application Service
Our after-sales service responds to your questions concern-
ing maintenance and repair of your product as well as spare
parts. You can find explosion drawings and information on
spare parts at: www.bosch-pt.com
The Bosch product use advice team will be happy to help you
with any questions about our products and their accessor-
ies.
In all correspondence and spare parts orders, please always
include the 10‑digit article number given on the nameplate
of the product.
Bosch Power Tools
Malaysia
Robert Bosch Sdn. Bhd.(220975-V) PT/SMY
No. 8A, Jalan 13/6
46200 Petaling Jaya
Selangor
Tel.: (03) 79663194
Toll-Free: 1800 880188
Fax: (03) 79583838
E-Mail: kiathoe.chong@my.bosch.com
www.bosch-pt.com.my
You can find further service addresses at:
www.bosch-pt.com/serviceaddresses
Disposal
The power tool, accessories and packaging should be re-
cycled in an environmentally friendly manner.
Do not dispose of power tools along with
household waste.
Français
Consignes de sécurité
Avertissements de sécurité généraux pour l'outil
Lire tous les avertissements de sé-
AVERTISSE-
curité et toutes les instructions.
MENT
Ne pas suivre les avertissements et
instructions peut donner lieu à un choc électrique, un incen-
die et/ou une blessure sérieuse.
Conserver tous les avertissements et toutes les instruc-
tions pour pouvoir s'y reporter ultérieurement.
Le terme «outil» dans les avertissements fait référence à
votre outil électrique alimenté par le secteur (avec cordon
d'alimentation) ou votre outil fonctionnant sur batterie (sans
cordon d'alimentation).
Sécurité de la zone de travail
Conserver la zone de travail propre et bien éclairée.
u
Les zones en désordre ou sombres sont propices aux ac-
cidents.
Ne pas faire fonctionner les outils électriques en at-
u
mosphère explosive, par exemple en présence de li-
quides inflammables, de gaz ou de poussières. Les ou-
tils électriques produisent des étincelles qui peuvent en-
flammer les poussières ou les fumées.
Maintenir les enfants et les personnes présentes à
u
l'écart pendant l'utilisation de l'outil. Les distractions
peuvent vous faire perdre le contrôle de l'outil.
Français | 13
1 609 92A 8TR | (10.01.2024)